ZoneMinder Wiki - User contributions [en]

Hikvision

2019-11-03T01:09:51Z

Kobold81: /* Hikvision DS-2DE2A404IW-DE3 */

=== Models ===

* [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

* [[Hikvision_DS_2CD2732FIS|Hikvision DS-2CD2732F-I(S) Megapixel Outdoor IP Dome Camera]]

* [[Hikvision_DS-2CD2532F-IWS|Hikvision DS-2CD2532F-IWS 3MP Outdoor IP Mini Dome Camera]]

* [[Hikvision_DS-2CD2012-I|Hikvision DS-2CD2012-I 1.3MP IR Mini Bullet Camera]]

* [[Hikvision_DS-2CD2332-I|Hikvision DS-2CD2332-I 3MP Outdoor Network Mini Dome Camera]]

* [[Hikvision_DS-2CD2022WD-I|Hikvision DS-2CD2022WD-I]]

*[[Hikvision_DS-2CD2025FWD-I | Hikvision DS-2CD2025FWD-i 1920x1080 30FPS Bullet]]

* [[Hikvision DS-2CD2142FWD-I|Hikvision DS-2CD2142FWD-I 4MP Mini Vandal Dome IP Camera PoE]]

* [[Hikvision DS-7204-7208-7216HVI-ST‎‎ | Hikvision DS-7204-7208-7216HVI-ST‎‎ IP Video Encoder DVR]] - Supports HD-TVI, Analog, and IP Cameras (has errors)

* [[Hikvision Video Doorbell DS-KB6003-WIP]]

* [[Hikvision DS-2DE2A404IW-DE3]]

* [[Hikvision DT2A404]]

For the [http://overseas.hikvision.com/en/Products_accessries_157_i3206.html DS-2CD2032-I] model, see the the DS-2CD2332-I model.

=== About ===

These seem to work. The biggest problem is people trying to use 'network camera' instead of 'ffmpeg' source type. Both have rtsp but only ffmpeg works here (because of h.264?) see [[http://www.cctvforum.com/viewtopic.php?f=19&t=37034]]

The '''DS-2CD2055FWD-I''' bullet works with ZM 1.30.4 with Ffmpeg.

The '''DS-2CD2632F-IS''' Update Version outdoor bullet works with ZM 1.30.4 ONVIF works for fast setup. See Model Specific Wiki page [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

The '''DS-2CD2732F-I''' and '''DS-2CD2032-I''' are tested.

[The DS-2CD2032-I's come in several different versions (Chinese, Int'l, English, etc...) each with multiple firmwares available. Be sure that you use the correct firmware for your camera model for best results.]

The '''DS-2CD2035-I''' outdoor bullet works using Ffmpeg.

The '''DS-2CD2532F-IWS''' was tested to work reliably only with Libvlc as source type.

The '''DS-2CD2012-I''' works too.

The '''DS-2CD2085FWD-I''' works too.

You can add some flags to the stream. An example is in the [http://forums.zoneminder.com/viewtopic.php?f=30&t=21651 forum] where ?tcp is added to the end of the stream to reduce artifacts.

=== Videostream: ===

== Hikvision DS-2DE2A404IW-DE3 ==
The Model Hikvision DT2A404 is a OEM version of the Hikvision DS-2DE2A404IW-DE3
IP after reset is 192.168.1.64

The following configuration is a example that is tested Zoneminder 1.32.3 but is expected to work with other versions, too.
The easy way ist to use the ONVIF Probe button in the upper right corner of each "Monitor" window.

In general, use the following configuration:
{| class="wikitable"
! style="text-align:center;" | Config Tab
! Option
! Config Setting
|-
|General
|Source Type
|Ffmpeg
|-
|rowspan="8"|Source
|Source Path
|to access the mainstream:
:rtsp://user:yourpassword@192.168.1.64:554/ch1/main/av_stream
:example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/main/av_stream
or
rtsp://user:yourpassword@192.168.1.64:554/Streaming/Channels/101?transportmode=mcast&profile=Profile_1

:
to access the substream:
:rtsp://192.168.0.1:554/ch1/sub/av_stream
:example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/sub/av_stream
|-
|Remote Method
|TCP or UDP
|-
|Target Colorspace
|32 bit colour
|-
|Capture Width (pixels)
|2560
|-
|Capture Height (pixels)
|1440
|-
|Preserve Aspect Ratio
|Unselected
|-
|Orientation
|Normal
|-
|Deinterlacing
|Disabled
|-
|rowspan="8"|Control
|-
|Control Type
|HikVision
|-
|Control Device (necessary for ptz,enter the exact camera model
|DS-2DE2A404IW-DE3
|-
|Control Address
|user:yourpassword@192.168.1.64
|-
|within the Hikvision Control Type: Protocol
|HikVision
|-
|}

==== General Tab ====
:Source Type : Ffmpeg / Libvlc / Remote(only some FW revisions)
==== Source Tab ====
:Source Path : rtsp://<username>:<password>@<ip_address>:<port>/Streaming/Channels/1?tcp
(example: rtsp://admin:12345@mycamera.mydomain.com//Streaming/Channels/1)
:Target Colorspace : 24 bit colour
:Capture Width (pixels) : 1280 (set these to match camera config)
:Capture Height (pixels) : 720

I also had to set max FPS slightly higher than set in camera, or i lost the lower half of the frame. (Camera seems to send 10.6fps when 10 is selected)

The following URL gives another Source path that was far more stable on Zoneminder 1.25: http://onlinetechadvice.blogspot.com/2014/04/hikvision-ds-2cd2032-i-working-in.html#comment-form

The Source path that worked for me is: rtsp://username:password@XXX.XXX.XXX.XXX:554/cam/realmonitor?channel=1&subtype=0?tcp
Of course, replace username and password and port with your specific installation information.

The "Remote" option also seems to work now in ZM 1.28 (at least with ds-2cd2032-i's of a certain firmware version), with less rtsp streaming errors than when using ffmpeg. The source path /Streaming/Channels/1 works fine with firmware version 5.1.6, but seems to not work any longer in 5.2.5. The source path /cam/realmonitor?channel=1&subtype=0 works on any firmware model. In ZM 1.28 (perhaps earlier as well), TCP is automatically forced when the "Remote" source type is chosen and RTP/RTSP is used (https://github.com/ZoneMinder/ZoneMinder/issues/323), so the trailing "?tcp" is not necessary for either URL when this configuration is used.

=== See Also ===

*[https://forums.zoneminder.com The forum] has multiple posts regarding Hikvision. Search there for more details.

Debian 13 Trixie with Zoneminder 1.36.35 or Zoneminder 1.37.x

2019-08-27T19:53:24Z

Kobold81:

== Debian 10 Buster with Zoneminder 1.32.3 from the Debian SID UNSTABLE repository

1. add unstable SID pachage sources to /etc/apt/sources.list
sudo nano /etc/apt/sources.list

add the following lines:
deb-src http://ftp.de.debian.org/debian/ sid main non-free contrib
deb http://ftp.de.debian.org/debian/ sid main non-free contrib

2. Update the package list
sudo apt-get update

3.Install zoneminder. When asked to install additional packages press 'y'
sudo apt-get -t sid install zoneminder

4. REMOVE the SID sources from /etc/apt/sources.list
sudo nano /etc/apt/sources.list

5. Continue here with "Step 6": https://zoneminder.readthedocs.io/en/stable/installationguide/debian.html#easy-way-debian-jessie

Debian 13 Trixie with Zoneminder 1.36.35 or Zoneminder 1.37.x

2019-08-27T19:51:14Z

Kobold81:

Debian 13 Trixie with Zoneminder 1.36.35 or Zoneminder 1.37.x

2019-08-27T19:50:42Z

Kobold81: /* Debian 10 Buster with Zoneminder 1.32.3 from the Debian Multimedia Repository */

== Debian 10 Buster with Zoneminder 1.32.3 from the Debian SID UNSTABLE repository

1. add unstable SID pachage sources to /etc/apt/sources.list
sudo nano /etc/apt/sources.list

add the following lines:
deb-src http://ftp.de.debian.org/debian/ sid main non-free contrib
deb http://ftp.de.debian.org/debian/ sid main non-free contrib

2. sudo apt-get update

3.Install zoneminder. When asked to install additional packages press 'y'
sudo apt-get -t sid install zoneminder

4. REMOVE the SID sources from /etc/apt/sources.list
sudo nano /etc/apt/sources.list

Hikvision

2019-02-07T18:56:20Z

Kobold81: /* Hikvision DS-2DE2A404IW-DE3 */

=== Models ===

* [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

* [[Hikvision_DS_2CD2732FIS|Hikvision DS-2CD2732F-I(S) Megapixel Outdoor IP Dome Camera]]

* [[Hikvision_DS-2CD2532F-IWS|Hikvision DS-2CD2532F-IWS 3MP Outdoor IP Mini Dome Camera]]

* [[Hikvision_DS-2CD2012-I|Hikvision DS-2CD2012-I 1.3MP IR Mini Bullet Camera]]

* [[Hikvision_DS-2CD2332-I|Hikvision DS-2CD2332-I 3MP Outdoor Network Mini Dome Camera]]

* [[Hikvision_DS-2CD2022WD-I|Hikvision DS-2CD2022WD-I]]

* [[Hikvision DS-2CD2142FWD-I|Hikvision DS-2CD2142FWD-I 4MP Mini Vandal Dome IP Camera PoE]]

* [[Hikvision DS-7204-7208-7216HVI-ST‎‎ | Hikvision DS-7204-7208-7216HVI-ST‎‎ IP Video Encoder DVR]] - Supports HD-TVI, Analog, and IP Cameras (has errors)

* [[Hikvision Video Doorbell DS-KB6003-WIP]]

* [[Hikvision DS-2DE2A404IW-DE3]]

* [[Hikvision DT2A404]]

For the [http://overseas.hikvision.com/en/Products_accessries_157_i3206.html DS-2CD2032-I] model, see the the DS-2CD2332-I model.

=== About ===

These seem to work. The biggest problem is people trying to use 'network camera' instead of 'ffmpeg' source type. Both have rtsp but only ffmpeg works here (because of h.264?) see [[http://www.cctvforum.com/viewtopic.php?f=19&t=37034]]

The '''DS-2CD2055FWD-I''' bullet works with ZM 1.30.4 with Ffmpeg.

The '''DS-2CD2632F-IS''' Update Version outdoor bullet works with ZM 1.30.4 ONVIF works for fast setup. See Model Specific Wiki page [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

The '''DS-2CD2732F-I''' and '''DS-2CD2032-I''' are tested.

[The DS-2CD2032-I's come in several different versions (Chinese, Int'l, English, etc...) each with multiple firmwares available. Be sure that you use the correct firmware for your camera model for best results.]

The '''DS-2CD2035-I''' outdoor bullet works using Ffmpeg.

The '''DS-2CD2532F-IWS''' was tested to work reliably only with Libvlc as source type.

The '''DS-2CD2012-I''' works too.

The '''DS-2CD2085FWD-I''' works too.

=== Videostream: ===

== Hikvision DS-2DE2A404IW-DE3 ==
The Model Hikvision DT2A404 is a OEM version of the Hikvision DS-2DE2A404IW-DE3
IP after reset is 192.168.1.64

The following configuration is a example that is tested Zoneminder 1.32.3 but is expected to work with other versions, too.

In general, use the following configuration:
{| class="wikitable"
! style="text-align:center;" | Config Tab
! Option
! Config Setting
|-
|General
|Source Type
|Ffmpeg
|-
|rowspan="8"|Source
|Source Path
|to access the mainstream:
:rtsp://admin:yourpassword@192.168.1.64:554/ch1/main/av_stream
:example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/main/av_stream
:
to access the substream:
:rtsp://192.168.0.1:554/ch1/sub/av_stream
:example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/sub/av_stream
|-
|Remote Method
|TCP or UDP
|-
|Target Colorspace
|32 bit colour
|-
|Capture Width (pixels)
|2560
|-
|Capture Height (pixels)
|1440
|-
|Preserve Aspect Ratio
|Unselected
|-
|Orientation
|Normal
|-
|Deinterlacing
|Disabled
|-
|rowspan="8"|Control
|-
|Control Type
|HikVision
|-
|Control Device
|can be left empty
|-
|Control Address
|admin:yourpassword@192.168.1.64:80
|-
|}

==== General Tab ====
:Source Type : Ffmpeg / Libvlc / Remote(only some FW revisions)
==== Source Tab ====
:Source Path : rtsp://<username>:<password>@<ip_address>:<port>/Streaming/Channels/1?tcp
(example: rtsp://admin:12345@mycamera.mydomain.com//Streaming/Channels/1)
:Target Colorspace : 24 bit colour
:Capture Width (pixels) : 1280 (set these to match camera config)
:Capture Height (pixels) : 720

I also had to set max FPS slightly higher than set in camera, or i lost the lower half of the frame. (Camera seems to send 10.6fps when 10 is selected)

The following URL gives another Source path that was far more stable on Zoneminder 1.25: http://onlinetechadvice.blogspot.com/2014/04/hikvision-ds-2cd2032-i-working-in.html#comment-form

The Source path that worked for me is: rtsp://username:password@XXX.XXX.XXX.XXX:554/cam/realmonitor?channel=1&subtype=0?tcp
Of course, replace username and password and port with your specific installation information.

The "Remote" option also seems to work now in ZM 1.28 (at least with ds-2cd2032-i's of a certain firmware version), with less rtsp streaming errors than when using ffmpeg. The source path /Streaming/Channels/1 works fine with firmware version 5.1.6, but seems to not work any longer in 5.2.5. The source path /cam/realmonitor?channel=1&subtype=0 works on any firmware model. In ZM 1.28 (perhaps earlier as well), TCP is automatically forced when the "Remote" source type is chosen and RTP/RTSP is used (https://github.com/ZoneMinder/ZoneMinder/issues/323), so the trailing "?tcp" is not necessary for either URL when this configuration is used.

=== See Also ===

*[https://forums.zoneminder.com The forum] has multiple posts regarding Hikvision. Search there for more details.

Hikvision

2019-02-07T18:46:26Z

Kobold81: /* Hikvision DS-2DE2A404IW-DE3 */

=== Models ===

* [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

* [[Hikvision_DS_2CD2732FIS|Hikvision DS-2CD2732F-I(S) Megapixel Outdoor IP Dome Camera]]

* [[Hikvision_DS-2CD2532F-IWS|Hikvision DS-2CD2532F-IWS 3MP Outdoor IP Mini Dome Camera]]

* [[Hikvision_DS-2CD2012-I|Hikvision DS-2CD2012-I 1.3MP IR Mini Bullet Camera]]

* [[Hikvision_DS-2CD2332-I|Hikvision DS-2CD2332-I 3MP Outdoor Network Mini Dome Camera]]

* [[Hikvision_DS-2CD2022WD-I|Hikvision DS-2CD2022WD-I]]

* [[Hikvision DS-2CD2142FWD-I|Hikvision DS-2CD2142FWD-I 4MP Mini Vandal Dome IP Camera PoE]]

* [[Hikvision DS-7204-7208-7216HVI-ST‎‎ | Hikvision DS-7204-7208-7216HVI-ST‎‎ IP Video Encoder DVR]] - Supports HD-TVI, Analog, and IP Cameras (has errors)

* [[Hikvision Video Doorbell DS-KB6003-WIP]]

* [[Hikvision DS-2DE2A404IW-DE3]]

* [[Hikvision DT2A404]]

For the [http://overseas.hikvision.com/en/Products_accessries_157_i3206.html DS-2CD2032-I] model, see the the DS-2CD2332-I model.

=== About ===

These seem to work. The biggest problem is people trying to use 'network camera' instead of 'ffmpeg' source type. Both have rtsp but only ffmpeg works here (because of h.264?) see [[http://www.cctvforum.com/viewtopic.php?f=19&t=37034]]

The '''DS-2CD2055FWD-I''' bullet works with ZM 1.30.4 with Ffmpeg.

The '''DS-2CD2632F-IS''' Update Version outdoor bullet works with ZM 1.30.4 ONVIF works for fast setup. See Model Specific Wiki page [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

The '''DS-2CD2732F-I''' and '''DS-2CD2032-I''' are tested.

[The DS-2CD2032-I's come in several different versions (Chinese, Int'l, English, etc...) each with multiple firmwares available. Be sure that you use the correct firmware for your camera model for best results.]

The '''DS-2CD2035-I''' outdoor bullet works using Ffmpeg.

The '''DS-2CD2532F-IWS''' was tested to work reliably only with Libvlc as source type.

The '''DS-2CD2012-I''' works too.

The '''DS-2CD2085FWD-I''' works too.

=== Videostream: ===

== Hikvision DS-2DE2A404IW-DE3 ==
The Model Hikvision DT2A404 is a OEM version of the Hikvision DS-2DE2A404IW-DE3
IP after reset is 192.168.1.64

The following configuration is a example that is tested Zoneminder 1.32.3 but is expected to work with other versions, too.

In general, use the following configuration:
{| class="wikitable"
! style="text-align:center;" | Config Tab
! Option
! Config Setting
|-
|General
|Source Type
|Ffmpeg
|-
|rowspan="8"|Source
|Source Path
|rtsp://admin:yourpassword@192.168.1.64:554/ch1/main/av_stream
example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/main/av_stream
|-
|Remote Method
|TCP or UDP
|-
|Target Colorspace
|32 bit colour
|-
|Capture Width (pixels)
|2560
|-
|Capture Height (pixels)
|1440
|-
|Preserve Aspect Ratio
|Unselected
|-
|Orientation
|Normal
|-
|Deinterlacing
|Disabled
|-
|rowspan="8"|Control
|-
|Control Type
|HikVision
|-
|Control Device
|can be left empty
|-
|Control Address
|admin:yourpassword@192.168.1.64:80
|-
|}

==== General Tab ====
:Source Type : Ffmpeg / Libvlc / Remote(only some FW revisions)
==== Source Tab ====
:Source Path : rtsp://<username>:<password>@<ip_address>:<port>/Streaming/Channels/1?tcp
(example: rtsp://admin:12345@mycamera.mydomain.com//Streaming/Channels/1)
:Target Colorspace : 24 bit colour
:Capture Width (pixels) : 1280 (set these to match camera config)
:Capture Height (pixels) : 720

I also had to set max FPS slightly higher than set in camera, or i lost the lower half of the frame. (Camera seems to send 10.6fps when 10 is selected)

The following URL gives another Source path that was far more stable on Zoneminder 1.25: http://onlinetechadvice.blogspot.com/2014/04/hikvision-ds-2cd2032-i-working-in.html#comment-form

The Source path that worked for me is: rtsp://username:password@XXX.XXX.XXX.XXX:554/cam/realmonitor?channel=1&subtype=0?tcp
Of course, replace username and password and port with your specific installation information.

The "Remote" option also seems to work now in ZM 1.28 (at least with ds-2cd2032-i's of a certain firmware version), with less rtsp streaming errors than when using ffmpeg. The source path /Streaming/Channels/1 works fine with firmware version 5.1.6, but seems to not work any longer in 5.2.5. The source path /cam/realmonitor?channel=1&subtype=0 works on any firmware model. In ZM 1.28 (perhaps earlier as well), TCP is automatically forced when the "Remote" source type is chosen and RTP/RTSP is used (https://github.com/ZoneMinder/ZoneMinder/issues/323), so the trailing "?tcp" is not necessary for either URL when this configuration is used.

=== See Also ===

*[https://forums.zoneminder.com The forum] has multiple posts regarding Hikvision. Search there for more details.

Hikvision

2019-02-07T18:46:02Z

Kobold81: /* Hikvision DS-2DE2A404IW-DE3 */

=== Models ===

* [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

* [[Hikvision_DS_2CD2732FIS|Hikvision DS-2CD2732F-I(S) Megapixel Outdoor IP Dome Camera]]

* [[Hikvision_DS-2CD2532F-IWS|Hikvision DS-2CD2532F-IWS 3MP Outdoor IP Mini Dome Camera]]

* [[Hikvision_DS-2CD2012-I|Hikvision DS-2CD2012-I 1.3MP IR Mini Bullet Camera]]

* [[Hikvision_DS-2CD2332-I|Hikvision DS-2CD2332-I 3MP Outdoor Network Mini Dome Camera]]

* [[Hikvision_DS-2CD2022WD-I|Hikvision DS-2CD2022WD-I]]

* [[Hikvision DS-2CD2142FWD-I|Hikvision DS-2CD2142FWD-I 4MP Mini Vandal Dome IP Camera PoE]]

* [[Hikvision DS-7204-7208-7216HVI-ST‎‎ | Hikvision DS-7204-7208-7216HVI-ST‎‎ IP Video Encoder DVR]] - Supports HD-TVI, Analog, and IP Cameras (has errors)

* [[Hikvision Video Doorbell DS-KB6003-WIP]]

* [[Hikvision DS-2DE2A404IW-DE3]]

* [[Hikvision DT2A404]]

For the [http://overseas.hikvision.com/en/Products_accessries_157_i3206.html DS-2CD2032-I] model, see the the DS-2CD2332-I model.

=== About ===

These seem to work. The biggest problem is people trying to use 'network camera' instead of 'ffmpeg' source type. Both have rtsp but only ffmpeg works here (because of h.264?) see [[http://www.cctvforum.com/viewtopic.php?f=19&t=37034]]

The '''DS-2CD2055FWD-I''' bullet works with ZM 1.30.4 with Ffmpeg.

The '''DS-2CD2632F-IS''' Update Version outdoor bullet works with ZM 1.30.4 ONVIF works for fast setup. See Model Specific Wiki page [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

The '''DS-2CD2732F-I''' and '''DS-2CD2032-I''' are tested.

[The DS-2CD2032-I's come in several different versions (Chinese, Int'l, English, etc...) each with multiple firmwares available. Be sure that you use the correct firmware for your camera model for best results.]

The '''DS-2CD2035-I''' outdoor bullet works using Ffmpeg.

The '''DS-2CD2532F-IWS''' was tested to work reliably only with Libvlc as source type.

The '''DS-2CD2012-I''' works too.

The '''DS-2CD2085FWD-I''' works too.

=== Videostream: ===

== Hikvision DS-2DE2A404IW-DE3 ==
The Model Hikvision DT2A404 is a OEM version of the Hikvision DS-2DE2A404IW-DE3
IP after reset is 192.168.1.64

The following configuration is a example that is tested Zoneminder 1.32.3 but is expected to work with other versions, too.

In general, use the following configuration:
{| class="wikitable"
! style="text-align:center;" | Config Tab
! Option
! Config Setting
|-
|General
|Source Type
|Ffmpeg
|-
|rowspan="8"|Source
|Source Path
|rtsp://admin:Scarab45321@192.168.1.64:554/ch1/main/av_stream
example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/main/av_stream
|-
|Remote Method
|TCP or UDP
|-
|Target Colorspace
|32 bit colour
|-
|Capture Width (pixels)
|2560
|-
|Capture Height (pixels)
|1440
|-
|Preserve Aspect Ratio
|Unselected
|-
|Orientation
|Normal
|-
|Deinterlacing
|Disabled
|-
|rowspan="8"|Control
|-
|Control Type
|HikVision
|-
|Control Device
|can be left empty
|-
|Control Address
|admin:yourpassword@192.168.1.64:80
|-
|}

==== General Tab ====
:Source Type : Ffmpeg / Libvlc / Remote(only some FW revisions)
==== Source Tab ====
:Source Path : rtsp://<username>:<password>@<ip_address>:<port>/Streaming/Channels/1?tcp
(example: rtsp://admin:12345@mycamera.mydomain.com//Streaming/Channels/1)
:Target Colorspace : 24 bit colour
:Capture Width (pixels) : 1280 (set these to match camera config)
:Capture Height (pixels) : 720

I also had to set max FPS slightly higher than set in camera, or i lost the lower half of the frame. (Camera seems to send 10.6fps when 10 is selected)

The following URL gives another Source path that was far more stable on Zoneminder 1.25: http://onlinetechadvice.blogspot.com/2014/04/hikvision-ds-2cd2032-i-working-in.html#comment-form

The Source path that worked for me is: rtsp://username:password@XXX.XXX.XXX.XXX:554/cam/realmonitor?channel=1&subtype=0?tcp
Of course, replace username and password and port with your specific installation information.

The "Remote" option also seems to work now in ZM 1.28 (at least with ds-2cd2032-i's of a certain firmware version), with less rtsp streaming errors than when using ffmpeg. The source path /Streaming/Channels/1 works fine with firmware version 5.1.6, but seems to not work any longer in 5.2.5. The source path /cam/realmonitor?channel=1&subtype=0 works on any firmware model. In ZM 1.28 (perhaps earlier as well), TCP is automatically forced when the "Remote" source type is chosen and RTP/RTSP is used (https://github.com/ZoneMinder/ZoneMinder/issues/323), so the trailing "?tcp" is not necessary for either URL when this configuration is used.

=== See Also ===

*[https://forums.zoneminder.com The forum] has multiple posts regarding Hikvision. Search there for more details.

Hikvision

2019-02-07T18:43:59Z

Kobold81: /* Videostream: */

=== Models ===

* [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

* [[Hikvision_DS_2CD2732FIS|Hikvision DS-2CD2732F-I(S) Megapixel Outdoor IP Dome Camera]]

* [[Hikvision_DS-2CD2532F-IWS|Hikvision DS-2CD2532F-IWS 3MP Outdoor IP Mini Dome Camera]]

* [[Hikvision_DS-2CD2012-I|Hikvision DS-2CD2012-I 1.3MP IR Mini Bullet Camera]]

* [[Hikvision_DS-2CD2332-I|Hikvision DS-2CD2332-I 3MP Outdoor Network Mini Dome Camera]]

* [[Hikvision_DS-2CD2022WD-I|Hikvision DS-2CD2022WD-I]]

* [[Hikvision DS-2CD2142FWD-I|Hikvision DS-2CD2142FWD-I 4MP Mini Vandal Dome IP Camera PoE]]

* [[Hikvision DS-7204-7208-7216HVI-ST‎‎ | Hikvision DS-7204-7208-7216HVI-ST‎‎ IP Video Encoder DVR]] - Supports HD-TVI, Analog, and IP Cameras (has errors)

* [[Hikvision Video Doorbell DS-KB6003-WIP]]

* [[Hikvision DS-2DE2A404IW-DE3]]

* [[Hikvision DT2A404]]

For the [http://overseas.hikvision.com/en/Products_accessries_157_i3206.html DS-2CD2032-I] model, see the the DS-2CD2332-I model.

=== About ===

These seem to work. The biggest problem is people trying to use 'network camera' instead of 'ffmpeg' source type. Both have rtsp but only ffmpeg works here (because of h.264?) see [[http://www.cctvforum.com/viewtopic.php?f=19&t=37034]]

The '''DS-2CD2055FWD-I''' bullet works with ZM 1.30.4 with Ffmpeg.

The '''DS-2CD2632F-IS''' Update Version outdoor bullet works with ZM 1.30.4 ONVIF works for fast setup. See Model Specific Wiki page [[Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet]]

The '''DS-2CD2732F-I''' and '''DS-2CD2032-I''' are tested.

[The DS-2CD2032-I's come in several different versions (Chinese, Int'l, English, etc...) each with multiple firmwares available. Be sure that you use the correct firmware for your camera model for best results.]

The '''DS-2CD2035-I''' outdoor bullet works using Ffmpeg.

The '''DS-2CD2532F-IWS''' was tested to work reliably only with Libvlc as source type.

The '''DS-2CD2012-I''' works too.

The '''DS-2CD2085FWD-I''' works too.

=== Videostream: ===

== Hikvision DS-2DE2A404IW-DE3 ==
The Model Hikvision DT2A404 is a OEM version of the Hikvision DS-2DE2A404IW-DE3
IP after reset is 192.168.1.64

The following configuration is a example that is tested Zoneminder 1.32.3 but is expected to work with other versions, too.

In general, use the following configuration:
{| class="wikitable"
! style="text-align:center;" | Config Tab
! Option
! Config Setting
|-
|General
|Source Type
|Ffmpeg
|-
|rowspan="8"|Source
|Source Path
|rtsp://admin:Scarab45321@192.168.1.64:554/ch1/main/av_stream
example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/main/av_stream
|-
|Remote Method
|TCP or UDP
|-
|Target Colorspace
|32 bit colour
|-
|Capture Width (pixels)
|2560
|-
|Capture Height (pixels)
|1440
|-
|Preserve Aspect Ratio
|Unselected
|-
|Orientation
|Normal
|-
|Deinterlacing
|Disabled
|-
|Control
|Control Type
|HikVision
|-
|Control Device
|can be left empty
|-
|Control Address
|admin:yourpassword@192.168.1.64:80
|}

==== General Tab ====
:Source Type : Ffmpeg / Libvlc / Remote(only some FW revisions)
==== Source Tab ====
:Source Path : rtsp://<username>:<password>@<ip_address>:<port>/Streaming/Channels/1?tcp
(example: rtsp://admin:12345@mycamera.mydomain.com//Streaming/Channels/1)
:Target Colorspace : 24 bit colour
:Capture Width (pixels) : 1280 (set these to match camera config)
:Capture Height (pixels) : 720

I also had to set max FPS slightly higher than set in camera, or i lost the lower half of the frame. (Camera seems to send 10.6fps when 10 is selected)

The following URL gives another Source path that was far more stable on Zoneminder 1.25: http://onlinetechadvice.blogspot.com/2014/04/hikvision-ds-2cd2032-i-working-in.html#comment-form

The Source path that worked for me is: rtsp://username:password@XXX.XXX.XXX.XXX:554/cam/realmonitor?channel=1&subtype=0?tcp
Of course, replace username and password and port with your specific installation information.

The "Remote" option also seems to work now in ZM 1.28 (at least with ds-2cd2032-i's of a certain firmware version), with less rtsp streaming errors than when using ffmpeg. The source path /Streaming/Channels/1 works fine with firmware version 5.1.6, but seems to not work any longer in 5.2.5. The source path /cam/realmonitor?channel=1&subtype=0 works on any firmware model. In ZM 1.28 (perhaps earlier as well), TCP is automatically forced when the "Remote" source type is chosen and RTP/RTSP is used (https://github.com/ZoneMinder/ZoneMinder/issues/323), so the trailing "?tcp" is not necessary for either URL when this configuration is used.

=== See Also ===

*[https://forums.zoneminder.com The forum] has multiple posts regarding Hikvision. Search there for more details.

Hikvision

2019-02-07T18:31:04Z

Kobold81: /* Models */

Dahua

2019-01-11T17:23:21Z

Kobold81: add dahua ipc-A35

= About =

Dahua is a Chinese manufacturer who produces a wide range of cameras, network video records, and related security hardware. Dahua devices are often shipped under the brand name "Alhua".

For more information on Dahua devices, consult [https://dahuawiki.com/USA/IPCamera/ Dahua Wiki US IP Cameras] ([https://web.archive.org/web/20180517190013/https://dahuawiki.com/USA/IPCamera/ Archive link]).

= Cameras =

Dahua has a well defined naming convention for their products which can be found here [https://dahuawiki.com/Template:NameConvention https://dahuawiki.com/Template:NameConvention] ([https://web.archive.org/web/20180517203721/https://dahuawiki.com/Template:NameConvention Archive link]). If there is a product you are looking to configure, but cannot find the correct settings for it, consult the [https://dahuawiki.com Dahua Wiki].

== IPC-HFW1200S ==
This camera *does* work with Zoneminder. Can access the camera's web page, but there is no documentation as to how to get to the image stream. The "webplugin.tar.gz" does not exist. Telnet port is open, but the default admin:admin does not log you in. The camera seems to be operating fine if you go through the RTSP protocol, and the settings I've used in the ZM monitor setup are:

General Tab:
Source Type: Ffmpeg

Source Tab:
Source Path: rtsp://admin:admin@192.168.1.100:554/cam/realmonitor?channel=1&subtype=0 (or subtype=1 for low res)
Remote Method: RTP/RTSP
The capture width and height need to be appropriate for the url given above, and if they're not then you'll
get no image. For subtype=0 use 1920x1080; and for subtype=1 use 352x240. These both work for me. There
may be other supported subtypes & resolutions.

== IPC-HDB4300C ==
This camera works perfectly as long as you have Zoneminder set up with FFMPEG.

=== Capabilities ===
Stream 0 is 1920 x 1080 @ 25fps and stream 1 is 708 x 576 @ 25fps. Both streams are compressed using H264 MPEG-4 AVC. The FFMPEG decoder is the way to go.

=== Initial Configuration ===
The camera defaults to an IP address of 192.168.1.108 with a username/password of admin/admin. It has a built-in web browser that lets you set a number of functions. The camera comes with a manual on a mini-CD. The manual is marginally useful. It is best just to get on the web interface and play.

Once you have played around a bit, it might be best if you reset the camera back to factory defaults. Under the dome cover there is a reset button. Hold it for at least five seconds. If you expect the red light to flash off and on or do something else interesting, you are going to be disappointed. The light stays on, but the unit does reset.
=== Help and Documentation ===
On the web interface, if you click on the question mark icon in the upper right corner of any page, you will get help... in Chinese. If you are not fluent in Chinese, I have some help for you. Copy the URL in the help window to a new window, replace "SimpleChinese" with "English" and hit Enter. Viola! Help in English.

Some of these help menus have information that is not contained anywhere else, so it is worth the time to go to each help page, do the substitution and read what is there.

Here is an example for the help page:

http://192.168.1.108/help/English/help.htm?device=1

Note that changing the device number at the end of the URL seems to change the functions listed in the help menu. I suspect that is because different Dahua devices have different capabilities, but they all use the same Web management interface.

=== Confirming Camera is On Your Network ===
Before I try to get a camera to work on Zoneminder, I try to look at it using the Swiss Army Knife of video tools, the VLC Player. Just download the player and put the following url into the File/Open Network dialog box:

rtsp://admin:admin@192.168.1.108

You should see pictures coming out of your camera. If you don't, then I am not going to be able to help you much. The camera does respond to pings, so you might try pinging it. If you can't ping it, you are not going to get very far.

You will find information on the Internet saying you need something like the following in order for it to work:

rtsp://admin:admin@192.168.1.108:554/live

This does work, but it does not seem to be necessary. Going to the IP address directly gets you to Stream 0 - the HD stream. You can see the properties of the stream using VLC by going to Window/Media Information/Codec Details. If you want to specifically point to the HD stream, use:

rtsp://admin:admin@192.168.1.108:554/cam/realmonitor?channel=1&subtype=0

To get to the SD or lower resolution feed, use:
rtsp://admin:admin@192.168.1.108:554/cam/realmonitor?channel=1&subtype=1

=== Setting up Zoneminder with the HDB4300C ===
I tried to get this camera to work with an older version of Zoneminder and had a devil of a time. In fact, I downloaded and compiled a new version of Zoneminder from scratch, and somehow managed to get it compiled ''without'' FFMPEG. The drop-down box was there, but it did not work. Anyway, I finally went to http://github.com/zoneminder and followed the directions for making an installation using Ubuntu, my preferred Linux distro, and everything worked just fine. But I will warn you at the beginning of this that, if you are getting Zoneminder up and running for the first time, it is possible to build it in a way that it won't work with this camera, even thought it looks like everything is fine. But don't worry - you won't have these problems, I'm sure...

Here are the settings I used for my Zoneminder setup. If I don't say anything about a setting, leave it alone - I started with a clean install of Zoneminder and I only changed the following things to get it to work with the camera:

General Tab
* Source type - FFMPEG

Source Tab
* Source Path - rtsp://admin:admin@192.168.1.108

That's it.

=== Advanced settings ===
As I mentioned before, this camera has at least two outputs (I believe it also has a snapshot output, but I have not discovered the path for it yet). You can get to the full resolution output using the Source Path above. If you use the web interface for the camera, and you go to 'Video", you will see that the main stream is H.264 1080P at 1920 x 1080, 25 frames per second. You will also see on the Sub-Stream tab that the lower resolution stream is also H.264 encoded at 352 x 288, 6 frames per second. This information is important if you want to get the full resolution from the camera in Zoneminder.

I use both outputs. The sub-stream is used for motion detection. When motion is detected on this feed, I then record the full resolution feed. Here are my settings. Again, if I don't mention a setting, leave it at the default value.

==== Full Resolution Stream ====
When I went with the default values in the camera and in Zoneminder, I ended up with vertical striping in the high resolution video stream. This appears to be a processing problem - I am guessing that Zoneminder cannot keep up. The feed looks normal when I view it using the web interface provided by the camera manufacturer, so that leaves out the camera and the network.

To fix the vertical striping, I reduced the frame rate for the main stream from 25 frames per second to 10 frames per second. Once I did that, I created a new monitor with the following settings:

===== General Tab =====
Source Type - Ffmpeg

===== Source Tab =====
Source Path- rtsp://admin:admin@YOURIPADDRESSHERE

Target Colorspace - 32 bit colour

Capture Width (pixels) - 1920

Capture Height (pixels) - 1080

==== Sub-Stream (lower resolution stream) ====
As mentioned above, this is a lower resolution stream so it consumes less network bandwidth and processing resources. Here are my settings for this stream:
===== General Tab =====
Source Type - Ffmpeg
===== Source Tab =====
Source Path - rtsp://admin:admin@YOURIPADDRESSHERE:554/cam/realmonitor?channel=1&subtype=1

Target Colourspace - 32 bit colour

Capture Width (pixels) - 352

Capture Height (pixels) - 288

=== Trigger at low resolution, capture at high resolution ===
Processing high resolution frames in order to detect motion can be costly from a computational standpoint. To lighten processor load, it is possible to set up two monitors - one for the sub-stream, and one for the primary high resolution stream.

On the General tab for the sub-stream monitor, set the Function to Modect. In this mode, Zoneminder will record events when motion is detected in this sub-stream feed.

On the General tab for the primary stream monitor, set the Function to Nodect. In this mode, Zoneminder will NOT record events based on motion detected in this feed. Put another way, your computer processor will not spend horsepower analyzing this high resolution feed (which takes more horsepower than analyzing the sub-stream feed).

Important: On the primary stream monitor, on the General tab, under Linked Monitors, click on the name of the sub-stream monitor (For example, if the sub-stream is Monitor-1, and the primary stream is Monitor-2, then click on Monitor-1). The name should turn blue. Save these settings.

Now, when motion is detected on the sub-stream feed, the sub-stream and the primary, high resolution stream will both be recorded. To unlink the primary montor from the sub-stream, Ctrl-click on the monitor name under Linked Monitors and save the settings.

== IPC-HDB3200C ==
*Source Type: Remote
*Remote Protocol: RTSP
*Remote Method: RTP/RTSP
*Remote Host Name: user:password@ip.address
*Remote Host Port: 554
*Remote Host Path: /cam/realmonitor?channel=1&subtype=0&tcp
*Target Colorspace: 24 bit colour
*Capture Width (pixels): 1920
*Capture Height (pixels): 1080
*Preserve Aspect Ratio: Unselected
*Orientation: Normal
*Deinterlacing: Disabled

Note that this camera can occasionally go into an 'indeterminate' state if power is interrupted or browned-out. When in this state, it will respond to pings and telnet, but will not stream an image. There is an app https://play.google.com/store/apps/details?id=nz.co.trillium.dahuareboot that will reboot it out of this state.

== HFW-4300S ==
*Source Type: FFMPEG
*Remote Protocol: RTSP
*Remote Method: RTP/RTSP/HTTP
*Source Path: rtsp://ip.address/live
*Target Colorspace: 24 bit colour
*Capture Width (pixels): 1920
*Capture Height (pixels): 1080
*Preserve Aspect Ratio: Unselected
*Orientation: Normal
*Deinterlacing: Disabled
*POE:Yes

Seems to be a good full 1080p camera for the price. Ordered via aliexpress.com

Issue with non IE based browsers, requires a plugin to access the video stream when directly accessing the administrative front end for the camera, so in Firefox or Chrome, you cannot see the video stream when accessing http://ip.address, works fine in Windows 10 Edge after fiddling with compatibility mode and downloading the plugin.

Have five of these running on a house security system at 720x576.

== IPC-HDBW4431R-ZS ==

The IPC-HDBW4431R-ZS is an PoE (802.3af) ONVIF compatible camera manufactured by Dahua as a part of their Eco-Savvy series. The Eco-Savvy series appears to be largely compatible hardware with the Dahua "Lite" series.

=== Configuration ===

{| class="wikitable"
! style="text-align:center;" | Config Tab
! Option
! Config Setting
|-
|General
|Source Type
|Ffmpeg
|-
|rowspan="8"|Source
|Source Path
|rtsp://admin:admin@192.168.1.100:554/cam/realmonitor?channel=1&subtype=0
|-
|Remote Method
|TCP
|-
|Target Colorspace
|24 bit colour
|-
|Capture Width (pixels)
|2560
|-
|Capture Height (pixels)
|1440
|-
|Preserve Aspect Ratio
|Unselected
|-
|Orientation
|Normal
|-
|Deinterlacing
|Disabled
|}

== Dahua IPC-A35 ==
The Dahua IPC-A35 can be found using zoneminder 1.32.x ONVIF "Monitor Probe" feature. At the Console screen, click on "Add" to add a new camera. Then on the top right, click on "ONVIF" and follow the configuration dialogue.

In general, use the following configuration:
{| class="wikitable"
! style="text-align:center;" | Config Tab
! Option
! Config Setting
|-
|General
|Source Type
|Ffmpeg
|-
|rowspan="8"|Source
|Source Path
|rtsp://admin:password@192.168.0.xxx:554/cam/realmonitor?channel=1&subtype=0&unicast=true&proto=Onvif
|-
|Remote Method
|UDP
|-
|Target Colorspace
|32 bit colour
|-
|Capture Width (pixels)
|1920
|-
|Capture Height (pixels)
|1080
|-
|Preserve Aspect Ratio
|Unselected
|-
|Orientation
|Normal
|-
|Deinterlacing
|Disabled
|}

=== Specs ===

* Compatible product page: [http://au.dahuasecurity.com/au/products/ipc-hdbw2431r-zsvfs-20067.html IPC-HDBW2431R-ZS] ([https://web.archive.org/web/20180517191508/http://au.dahuasecurity.com/au/products/ipc-hdbw2431r-zsvfs-20067.html Archive link])
* Specification Sheet: [[Media:IPC-HDBW4431R-ZS.pdf]]
* "Lite" Series equivalent spec sheet: [[Media:DH-IPC-HDBW2431R-ZSVFS_Datasheet_20180202.pdf]]

=== Possible Compatible models ===
* DH-IPC-HDBW2431RP-ZS - 4MP WDR IR Dome Network Camera, PAL
* DH-IPC-HDBW2431RN-ZS - 4MP WDR IR Dome Network Camera, NTSC
* IPC-HDBW2431RP-ZS - 4MP WDR IR Dome Network Camera, PAL
* IPC-HDBW2431RN-ZS - 4MP WDR IR Dome Network Camera, NTSC
* DH-IPC-HDBW2431RP-VFS - 4MP WDR IR Dome Network Camera, PAL
* DH-IPC-HDBW2431RN-VFS - 4MP WDR IR Dome Network Camera, NTSC
* IPC-HDBW2431RP-VFS - 4MP WDR IR Dome Network Camera, PAL
* IPC-HDBD2431RN-VFS - 4MP WDR IR Dome Network Camera, NTSC

In addition it ''may'' be compatible with the following models:

* DH-IPC-HDBW4431RP-ZS - 4MP WDR IR Dome Network Camera, PAL
* DH-IPC-HDBW4431RN-ZS - 4MP WDR IR Dome Network Camera, NTSC
* IPC-HDBW4431RP-ZS - 4MP WDR IR Dome Network Camera, PAL
* IPC-HDBW4431RN-ZS - 4MP WDR IR Dome Network Camera, NTSC
* DH-IPC-HDBW4431RP-VFS - 4MP WDR IR Dome Network Camera, PAL
* DH-IPC-HDBW4431RN-VFS - 4MP WDR IR Dome Network Camera, NTSC
* IPC-HDBW4431RP-VFS - 4MP WDR IR Dome Network Camera, PAL
* IPC-HDBD4431RN-VFS - 4MP WDR IR Dome Network Camera, NTSC
* DH-IPC-HDBW4431R-ZS - 4MP WDR IR Dome Network Camera
* IPC-HDBW4431R-ZS - 4MP WDR IR Dome Network Camera
* DH-IPC-HDBW4431R-VFS - 4MP WDR IR Dome Network Camera
* IPC-HDBW4431R-VFS - 4MP WDR IR Dome Network Camera