TP-LINK

2024-05-19T14:05:01Z

Otaci: Add some details about newer models.

= Models =

== C100 Tapo ==

GENERAL

# Check IP address either at Tapo app or via your router
# Create user and password (those you will need later to access video streams) at Tapo app: Camera Settings > Advanced Settings > Camera Account

Cameras will be detected by ONVIF function, choose 1920x1080 or 640x480 pixel.

=== C110 TAPO ===
Same as C100.

Example source path: rtsp://username:password@ip_address:554/stream1

Capture height: 2304 x 1296

== C310 TAPO ==

GENERAL

# Check IP address either at Tapo app or via your router
# Create user and password (those you will need later to create source link) at Tapo app: Camera Settings > Advanced Settings > Camera Account
# You can use [https://www.ispyconnect.com/camera/tapo iSPY generator] to create source link or build based on below settings:

SOURCE
* Source Type: FFMPEG
* URL: rtsp://''user'':''password''@<ip_address>:554/stream1 ''port number may be different''
* Capture Width: 1920
* Capture Height: 1080

Same for C320WS.

== NC250 ==

GENERAL
* Source Type: cURL (HTTP(S) only)
SOURCE
* URL: http://<ip_address>:8080/stream/video/mjpeg
* Username: admin
* Password ("admin" base64 encoded): YWRtaW4=
* Capture Width: 1280
* Capture Height: 720

== NC450 ==
obtained via ONVIF Device Manager
* NC450(UN)
* 1.2.4 Build 170322 Rel.85B2CB
* http://<ip_address>:2020/onvif/device_service

=== on zoneminder v1.35.23 ===
GENERAL
* source type: Ffmpeg
SOURCE
* Source Path: rtsp://<admin:passwd>@<ip_address>:554/h264_hd.sdp (neither user nor pass is encoded )
* Target colorspace: 32 color
* Capture Width: 1280
* Capture Height: 720
* control http://<user:pass>@<ip_address>:2020/onvif/device_service ( user:pass plain ascii text )
* Auto Stop Timeout stop 0.5

== TL-SC3000 ==

See [[TLSC-3000]]

== TL-SC3171/G ==

See [[SC-3171]]

== TL-SC3130/G ==

=== Getting MJPEG streams ===

* Disable RTSP
* Disable Audio Codec
* Point your monitor to a "remote" "simple" source to an "http" server at your camera's ip address with <code>/video.mjpg</code> path, match width & height to whatever you choose at the "MJPEG" configuration page in the camera settings, use 24 for color depth.

Tested working fine with viewer authentication disabled and enabled (put <code><user>:<password>@<camera-ip></code> in server address) also with uPnP enabled & disabled.

Worked fine over wifi at maximum resolution and color depth allowed by the camera of 640x480 24bpp 30fps, on fixed "excelent" quality.

=== Getting MPEG streams ===

* Enable RTSP in the camera (leaving the default RTSP port of 554, otherwise modify appropriately the following steps' URLs)
* Point your monitor to an ffmpeg source to <code>rtsp://<camera-ip>/video.mp4</code> to get the stream configured as the MPEG4 "Computer View" in your camera, so you must match width & height to whatever you configure there, and set 24 for color depth or...
* Point your monitor to an ffmpeg source to <code>rtsp://<camera-ip>/video.3gp</code> to get the stream configured as the MPEG4 "Mobile View" in your camera, so you must match width & height to whatever you configure there, and set 24 for color depth.

Tested working fine with audio codec enabled & disabled, with multicast streaming enabled & disabled, with viewer authentication disable & enabled (put <code>rtsp://<user>:<password>@<camera-ip>/...</code> in above URLs) and with uPnP enabled & disabled.

In both cases worked fine over wifi at maximum resolutions and color depths allowed by the camera in each case (640x480 24bpp 30fps, on fixed "excelent" quality on "Computer View"'s mp4 and 320x240 24bpp 10fps, on fixed "excelent" quality on "Mobile View"'s 3gp streams).

The side effect is that MJPEG stream is disabled when you enable RTSP for accessing MPEG streams, so you can't do both at the same time.

== TL-SC3230 ==

The camera has a maximum of 8 videos profiles. By default 5 of them are H264 streams and 3 are MJPEG stream. It can stream both codec at the same time.

=== Getting streams ===

* Point your monitor to an ffmpeg source to <code>rtsp://<camera-ip>/media.amp?streamprofile=<profile-name>&audio=0</code> to get the stream. If no profile is specified it will stream the first profile.

Tested working fine with audio codec enabled & disabled, with multicast streaming enabled & disabled, with viewer authentication disable & enabled (put <code>rtsp://<user>:<password>@<camera-ip>/...</code> in above URLs) and with uPnP enabled & disabled.

ZoneMinder Wiki - User contributions [en]

TP-LINK