ZoneMinder Wiki - User contributions [en]

How to stream h264 with ffmpeg from an Axis P3343

2012-08-05T05:41:34Z

Pashdown: avconv dependency is installed

--[[User:Stagecoach|stagecoach]] 12:45, 19 October 2010 (BST)

Go back to the [[How_To|How To]] pages...

=Introduction=
We are trying to get h264 capturing and recording going in ZM. This page provides a starting point. The goal of this page is to test and make sure that h264 streaming is working in principal.

=Reference=

[http://rob.opendot.cl/index.php/useful-stuff/ffmpeg-x264-encoding-guide/ FFmpeg x264 encoding guide]

=x264 Preset Files=
If you build ffmpeg from scratch, then the preset files are by default located in /usr/local/share/ffmpeg

=General Camera Configuration=

==Variable Bit Rate==
Camera Settings:
[[Image:AX H264 VBR 1.png|thumb|Variable Bit Rate configuration]]

ffmpeg command:
two-pass vbr:
ffmpeg -t 00:00:30 -f rtsp -i rtsp://172.16.2.100:554/axis-media/media.amp -an -pass 1 -vcodec libx264 -vpre slow_firstpass -b 180000 -bt 180000 -threads 0 -y outfile.mp4

Output file plays back in Totem Media Player.

==Constant Bit Rate==
Camera Settings:
[[Image:AX H264 CBR 1.png|thumb|Constant Bit Rate configuration]]

ffmpeg command:
ffmpeg -t 00:00:30 -f rtsp -i rtsp://172.16.2.100:554/axis-media/media.amp -vcodec libx264 -vpre medium -crf 20.0 -b 180000 -threads 0 -y outfile.mp4

Output file plays back in Totem Media Player.

=Ubuntu 12.04 Configuration=
After much searching and researching, this configuration works for me for the Axis P3343, M3014, and M3011.

The default Ubuntu 12.04 ffmpeg, or "avconv" as the new fork is known as, works fine for camera capture, h264 video construction, and EyeZM. It is automatically installed as a dependency to the zoneminder package.

Set the following options for Zoneminder under the '''Images''' tab:

:'''OPT_FFMPEG:''' (Checked)
:'''PATH_FFMPEG:''' /usr/bin/avconv

Add the Zoneminder cameras with the following settings:

'''General'''
:'''Source Type:''' Ffmpeg
:'''Maximum FPS:''' Empty
:'''Alarm Maximum FPS:''' Empty

'''Source'''
:'''Source Path:''' rtsp://(camera dns name or IP address)/axis-media/media.amp?streamprofile=Quality?tcp
:'''Capture Width (pixels):''' 640 for the M3011, 1280 for the P3343 and the M3014
:'''Capture Height (pixels):''' 480 for the M3011, 800 for the P3343 and the M3014

If your camera status repeatedly goes orange or red, copy the "Quality" profile on the camera and setup a "ZM" profile on the camera with '''GOV Settings''' length of 20. Note that this is usually due to the camera trying to handle multiple streams. It can usually do the "Quality" profile just fine if it is only serving 1 stream.

The "?tcp" argument on the Source Path URL is critical. Otherwise you will get packets dropped and half and artifacted frames.

How to stream h264 with ffmpeg from an Axis P3343

2012-08-05T05:40:43Z

Pashdown: up the level

--[[User:Stagecoach|stagecoach]] 12:45, 19 October 2010 (BST)

Go back to the [[How_To|How To]] pages...

=Introduction=
We are trying to get h264 capturing and recording going in ZM. This page provides a starting point. The goal of this page is to test and make sure that h264 streaming is working in principal.

=Reference=

[http://rob.opendot.cl/index.php/useful-stuff/ffmpeg-x264-encoding-guide/ FFmpeg x264 encoding guide]

=x264 Preset Files=
If you build ffmpeg from scratch, then the preset files are by default located in /usr/local/share/ffmpeg

=General Camera Configuration=

==Variable Bit Rate==
Camera Settings:
[[Image:AX H264 VBR 1.png|thumb|Variable Bit Rate configuration]]

ffmpeg command:
two-pass vbr:
ffmpeg -t 00:00:30 -f rtsp -i rtsp://172.16.2.100:554/axis-media/media.amp -an -pass 1 -vcodec libx264 -vpre slow_firstpass -b 180000 -bt 180000 -threads 0 -y outfile.mp4

Output file plays back in Totem Media Player.

==Constant Bit Rate==
Camera Settings:
[[Image:AX H264 CBR 1.png|thumb|Constant Bit Rate configuration]]

ffmpeg command:
ffmpeg -t 00:00:30 -f rtsp -i rtsp://172.16.2.100:554/axis-media/media.amp -vcodec libx264 -vpre medium -crf 20.0 -b 180000 -threads 0 -y outfile.mp4

Output file plays back in Totem Media Player.

=Ubuntu 12.04 Configuration=
After much searching and researching, this configuration works for me for the Axis P3343, M3014, and M3011.

The default Ubuntu 12.04 ffmpeg, or "avconv" as the new fork is known as, works fine for camera capture, h264 video construction, and EyeZM.

Set the following options for Zoneminder under the '''Images''' tab:

:'''OPT_FFMPEG:''' (Checked)
:'''PATH_FFMPEG:''' /usr/bin/avconv

Add the Zoneminder cameras with the following settings:

'''General'''
:'''Source Type:''' Ffmpeg
:'''Maximum FPS:''' Empty
:'''Alarm Maximum FPS:''' Empty

'''Source'''
:'''Source Path:''' rtsp://(camera dns name or IP address)/axis-media/media.amp?streamprofile=Quality?tcp
:'''Capture Width (pixels):''' 640 for the M3011, 1280 for the P3343 and the M3014
:'''Capture Height (pixels):''' 480 for the M3011, 800 for the P3343 and the M3014

If your camera status repeatedly goes orange or red, copy the "Quality" profile on the camera and setup a "ZM" profile on the camera with '''GOV Settings''' length of 20. Note that this is usually due to the camera trying to handle multiple streams. It can usually do the "Quality" profile just fine if it is only serving 1 stream.

The "?tcp" argument on the Source Path URL is critical. Otherwise you will get packets dropped and half and artifacted frames.

How to stream h264 with ffmpeg from an Axis P3343

2012-08-05T05:40:09Z

Pashdown: remove unnecessary severinson ffmpeg, update for avconv

--[[User:Stagecoach|stagecoach]] 12:45, 19 October 2010 (BST)

Go back to the [[How_To|How To]] pages...

=Introduction=
We are trying to get h264 capturing and recording going in ZM. This page provides a starting point. The goal of this page is to test and make sure that h264 streaming is working in principal.

=Reference=

[http://rob.opendot.cl/index.php/useful-stuff/ffmpeg-x264-encoding-guide/ FFmpeg x264 encoding guide]

=x264 Preset Files=
If you build ffmpeg from scratch, then the preset files are by default located in /usr/local/share/ffmpeg

=General Camera Configuration=

==Variable Bit Rate==
Camera Settings:
[[Image:AX H264 VBR 1.png|thumb|Variable Bit Rate configuration]]

ffmpeg command:
two-pass vbr:
ffmpeg -t 00:00:30 -f rtsp -i rtsp://172.16.2.100:554/axis-media/media.amp -an -pass 1 -vcodec libx264 -vpre slow_firstpass -b 180000 -bt 180000 -threads 0 -y outfile.mp4

Output file plays back in Totem Media Player.

==Constant Bit Rate==
Camera Settings:
[[Image:AX H264 CBR 1.png|thumb|Constant Bit Rate configuration]]

ffmpeg command:
ffmpeg -t 00:00:30 -f rtsp -i rtsp://172.16.2.100:554/axis-media/media.amp -vcodec libx264 -vpre medium -crf 20.0 -b 180000 -threads 0 -y outfile.mp4

Output file plays back in Totem Media Player.

==Ubuntu 12.04 Configuration==
After much searching and researching, this configuration works for me for the Axis P3343, M3014, and M3011.

The default Ubuntu 12.04 ffmpeg, or "avconv" as the new fork is known as, works fine for camera capture, h264 video construction, and EyeZM.

Set the following options for Zoneminder under the '''Images''' tab:

:'''OPT_FFMPEG:''' (Checked)
:'''PATH_FFMPEG:''' /usr/bin/avconv

Add the Zoneminder cameras with the following settings:

'''General'''
:'''Source Type:''' Ffmpeg
:'''Maximum FPS:''' Empty
:'''Alarm Maximum FPS:''' Empty

'''Source'''
:'''Source Path:''' rtsp://(camera dns name or IP address)/axis-media/media.amp?streamprofile=Quality?tcp
:'''Capture Width (pixels):''' 640 for the M3011, 1280 for the P3343 and the M3014
:'''Capture Height (pixels):''' 480 for the M3011, 800 for the P3343 and the M3014

If your camera status repeatedly goes orange or red, copy the "Quality" profile on the camera and setup a "ZM" profile on the camera with '''GOV Settings''' length of 20. Note that this is usually due to the camera trying to handle multiple streams. It can usually do the "Quality" profile just fine if it is only serving 1 stream.

The "?tcp" argument on the Source Path URL is critical. Otherwise you will get packets dropped and half and artifacted frames.

How to stream h264 with ffmpeg from an Axis P3343

2012-08-03T21:02:54Z

Pashdown: add the specific ubuntu 12.04 configuration

--[[User:Stagecoach|stagecoach]] 12:45, 19 October 2010 (BST)

Go back to the [[How_To|How To]] pages...

=Introduction=
We are trying to get h264 capturing and recording going in ZM. This page provides a starting point. The goal of this page is to test and make sure that h264 streaming is working in principal.

=Reference=

[http://rob.opendot.cl/index.php/useful-stuff/ffmpeg-x264-encoding-guide/ FFmpeg x264 encoding guide]

=x264 Preset Files=
If you build ffmpeg from scratch, then the preset files are by default located in /usr/local/share/ffmpeg

=General Camera Configuration=

==Variable Bit Rate==
Camera Settings:
[[Image:AX H264 VBR 1.png|thumb|Variable Bit Rate configuration]]

ffmpeg command:
two-pass vbr:
ffmpeg -t 00:00:30 -f rtsp -i rtsp://172.16.2.100:554/axis-media/media.amp -an -pass 1 -vcodec libx264 -vpre slow_firstpass -b 180000 -bt 180000 -threads 0 -y outfile.mp4

Output file plays back in Totem Media Player.

==Constant Bit Rate==
Camera Settings:
[[Image:AX H264 CBR 1.png|thumb|Constant Bit Rate configuration]]

ffmpeg command:
ffmpeg -t 00:00:30 -f rtsp -i rtsp://172.16.2.100:554/axis-media/media.amp -vcodec libx264 -vpre medium -crf 20.0 -b 180000 -threads 0 -y outfile.mp4

Output file plays back in Totem Media Player.

==Zoneminder Ubuntu 12.04 Configuration==
After much searching and researching, this configuration works for me for the Axis P3343, M3014, and M3011.

Install ffmpeg from the Jon Severinsson PPA:
<pre>
sudo apt-get install python-software-properties
sudo add-apt-repository ppa:jon-severinsson/ffmpeg
sudo apt-get update
sudo apt-get install -V ffmpeg
</pre>

Set the following option for Zoneminder under the '''Images''' tab:

'''FFMPEG_INPUT_OPTIONS:''' "-rtsp_flags filter_src -an"

Add the Zoneminder cameras with the following settings:

'''General'''
:'''Source Type:''' Ffmpeg
:'''Maximum FPS:''' Empty
:'''Alarm Maximum FPS:''' Empty

'''Source'''
:'''Source Path:''' rtsp://(camera dns name or IP address)/axis-media/media.amp?streamprofile=Quality?tcp
:'''Capture Width (pixels):''' 640 for the M3011, 1280 for the P3343 and the M3014
:'''Capture Height (pixels):''' 480 for the M3011, 800 for the P3343 and the M3014

If your camera status repeatedly goes orange or red, copy the "Quality" profile on the camera and setup a "ZM" profile on the camera with '''GOV Settings''' length of 20. Note that this is usually due to the camera trying to handle multiple streams. It can do the "Quality" profile just fine if it is only serving 1 stream.

The "?tcp" argument on the Source Path URL is critical. Otherwise you will get packets dropped and half and artifacted frames.