ZoneMinder Wiki - User contributions [en]

Escam

2015-12-10T15:45:45Z

Redbeard4:

=QD900 settings=
For RTSP feed, set ZM source to ffmpeg (or libvlc, but in my testing libvlc is less reliable).

====Configuring it via FFMPEG====
* General
**Source Type-->Ffmpeg

* Source
** Source Path
*** For primary stream: '''rtsp://<cameraip>:554/11'''
====Configuring it via MJPEG====
* General
**Source Type-->Remote
* Source
** Remote Protocol
*** HTTP
** Remote Method
*** Simple
** Remote Host Name
*** <camera ip>
** Remote Port
*** 80
** Remote Host Path
*** /cgi-bin/hi3510/snap.cgi?&-getstream&-chn=1

=QD300 settings=

==In camera settings==

Note: these are settings I made directly in the camera's UI - I did not install Escam's CMS software

QD300 allows you to configure both a primary and secondary stream. You can set it up in the "device config->Encode" section of the camera

In this example, I've enabled the primary stream and disabled the secondary stream. You can enable both. Note that I've set the FPS to 3 as its a good idea to reduce FPS in-camera and not ZoneMinder. Set it to a value that makes sense for you.

[[File:Qd300-settings.png]]

==ZoneMinder settings==

You can either configure the camera using FFmpeg or native RTSP

====Configuring it via FFMPEG====

* General
**Source Type-->Ffmpeg

* Source
** Source Path
*** For primary stream: '''rtsp://<cameraip>:554/user=<username>&password=<password>&channel=1&stream=0.sdp'''
*** For secondary stream: '''rtsp://<cameraip>:554/user=<username>&password=<password>&channel=2&stream=0.sdp'''
** Remote Method: RTP/RTSP
** Options: keep empty
** Target colorspace: 32 bit
** Capture Width and Height
*** For primary stream: 1280 and 720
*** For secondary stream: if you are using CIF, its 352 and 288 respectively

You don't need to change anything else

====Configuring it via native RTSP====

Note that using the native RTSP player in ZM results in error frames while decoding what seems to be key frames.

Here is the error I see (even though it actually seems to perform better than FFMPEG mode)

zmc_m7[27558]: ERR [Error while decoding frame 1116]
zmc_m7[27558]: ERR [8: 00 00 01 06 e5 01 2c 80]

* General
**Source Type-->Remote

* Source
** Remote Protocol: RTSP
** Remote Method: RTP/RTSP
** Remote Host Name: <IP address of FQDN of camera>
** Remote Host Port: 554
** Remote Host Path:
*** For primary stream: '''/user=<username>&password=<password>&channel=1&stream=0.sdp'''
*** For secondary stream: '''/user=<username>&password=<password>&channel=1&stream=0.sdp'''

** Target colorspace: 32 bit
** Capture Width and Height
*** For primary stream: 1280 and 720
*** For secondary stream: if you are using CIF, its 352 and 288 respectively

You don't need to change anything else

Escam

2015-12-10T15:44:37Z

Redbeard4:

=QD900 settings=
For RTSP feed, set ZM source to ffmpeg (or libvlc, but in my testing libvlc is less reliable).

====Configuring it via FFMPEG====
* General
**Source Type-->Ffmpeg

* Source
** Source Path
*** For primary stream: '''rtsp://<cameraip>:554/11'''
====Configuring it via MJPEG====
* General
**Source Type-->Remote
* Source
** Remote Protocol
*** HTTP
** Remote Method
*** Simple
** Remote Host Name
*** <camera ip>
** Remote Port
*** 80
** Remote Host Path
*** /cgi-bin/hi3510/snap.cgi?&-getstream&-chn=1

With this camera, you can also login to it as root via telnet. Username: root, Password: cat1029

=QD300 settings=

==In camera settings==

Note: these are settings I made directly in the camera's UI - I did not install Escam's CMS software

QD300 allows you to configure both a primary and secondary stream. You can set it up in the "device config->Encode" section of the camera

In this example, I've enabled the primary stream and disabled the secondary stream. You can enable both. Note that I've set the FPS to 3 as its a good idea to reduce FPS in-camera and not ZoneMinder. Set it to a value that makes sense for you.

[[File:Qd300-settings.png]]

==ZoneMinder settings==

You can either configure the camera using FFmpeg or native RTSP

====Configuring it via FFMPEG====

* General
**Source Type-->Ffmpeg

* Source
** Source Path
*** For primary stream: '''rtsp://<cameraip>:554/user=<username>&password=<password>&channel=1&stream=0.sdp'''
*** For secondary stream: '''rtsp://<cameraip>:554/user=<username>&password=<password>&channel=2&stream=0.sdp'''
** Remote Method: RTP/RTSP
** Options: keep empty
** Target colorspace: 32 bit
** Capture Width and Height
*** For primary stream: 1280 and 720
*** For secondary stream: if you are using CIF, its 352 and 288 respectively

You don't need to change anything else

====Configuring it via native RTSP====

Note that using the native RTSP player in ZM results in error frames while decoding what seems to be key frames.

Here is the error I see (even though it actually seems to perform better than FFMPEG mode)

zmc_m7[27558]: ERR [Error while decoding frame 1116]
zmc_m7[27558]: ERR [8: 00 00 01 06 e5 01 2c 80]

* General
**Source Type-->Remote

* Source
** Remote Protocol: RTSP
** Remote Method: RTP/RTSP
** Remote Host Name: <IP address of FQDN of camera>
** Remote Host Port: 554
** Remote Host Path:
*** For primary stream: '''/user=<username>&password=<password>&channel=1&stream=0.sdp'''
*** For secondary stream: '''/user=<username>&password=<password>&channel=1&stream=0.sdp'''

** Target colorspace: 32 bit
** Capture Width and Height
*** For primary stream: 1280 and 720
*** For secondary stream: if you are using CIF, its 352 and 288 respectively

You don't need to change anything else

Escam

2015-12-10T15:32:05Z

Redbeard4: