View source for WinFast TV2000 XP

This card uses a bt878 chipset and the bttv kernel module and is probably one of the more common capture cards found in a home PC/DVR. It is quite generic but comes in 2 flavours: "ATX version" and "Low profile version"

There are 4 inputs:
# '''Television''' (Coaxial cable) This is where you can tune to a TV channel frequency
# '''Composite1''' (RCA lead)
# '''SVideo''' (MiniDIN connector)
# '''Composite3''' (RCA lead) This is the FM tuner for radio

'''Note:''' You should have a connector cable to connect the Composite1 and SVideo cables into a single 6-pin MiniDIN port on the card. The cable for the Low profile version also includes the Left/Right Audio inputs, connecting to a 9-pin MiniDIN port on the card.

There is also an input for the Infrared sensor which plugs into a headphone jack. This is probably not useful for ZoneMinder but may be used with Linux InfraRed Control (LIRC) if you want to capture from TV occasionally.

== dmesg ==
<pre>
Linux video capture interface: v2.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
GSI 23 sharing vector 0xE9 and IRQ 23
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 23
bttv0: Bt878 (rev 17) at 0000:01:07.0, irq: 23, latency: 32, mmio: 0xe5100000
bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID is 107d:6606
bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00bff706 [init]
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner 5-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner 5-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
input: bttv IR (card=34) as /class/input/input7
bttv-input: bttv IR (card=34) detected at pci-0000:01:07.0/ir0
</pre>

== lspci ==
<pre>
helot# lspci | grep Bt878
01:07.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
01:07.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
</pre>

== xawtv -hwscan ==
<pre>
helot# xawtv -hwscan
This is xawtv-3.95, running on Linux/x86_64 (2.6.18-ck1)
looking for available devices

/dev/video0: OK                         [ -device /dev/video0 ]
    type : v4l2
    name : BT878 video (Leadtek WinFast 20
    flags: overlay capture tuner
</pre>

When you run <tt>xawtv</tt>, you may need to fiddle with some of the options. In my case, I set the ''''input'''' to '''Composite1''' and ''''capture'''' to '''grabdisplay'''. Once you have a picture, you can adjust the colour, contrast, brightness etc. ZoneMinder will recognise these settings when you set up a Monitor for this input (you may need to leave xawtv running).

== zmu -d <device> -q -v ==
<pre>
helot# zmu -d /dev/video0 -q -v
Video Capabilities
  Name: BT878 video (Leadtek WinFast 20
  Type: 171
    Can capture
    Can tune
    Overlay onto frame buffer
    Can clip
    Scalable
  Video Channels: 4
  Audio Channels: 1
  Maximum Width: 924
  Maximum Height: 576
  Minimum Width: 48
  Minimum Height: 32
Window Attributes
  X Offset: 0
  Y Offset: 0
  Width: 384
  Height: 288
Picture Attributes
  Palette: 5 - 32bit RGB
  Colour Depth: 32
  Brightness: 27086
  Hue: 22280
  Colour :47185
  Contrast: 25340
  Whiteness: 0
Channel 0 Attributes
  Name: Television
  Channel: 0
  Flags: 3
    Channel has a tuner
    Channel has audio
  Type: 1 - TV
  Format: 0 - PAL
Channel 1 Attributes
  Name: Composite1
  Channel: 1
  Flags: 2
    Channel has audio
  Type: 2 - Camera
  Format: 0 - PAL
Channel 2 Attributes
  Name: S-Video
  Channel: 2
  Flags: 2
    Channel has audio
  Type: 2 - Camera
  Format: 0 - PAL
Channel 3 Attributes
  Name: Composite3
  Channel: 3
  Flags: 2
    Channel has audio
  Type: 2 - Camera
  Format: 0 - PAL
</pre>

== Configuring a Monitor ==
In the ZoneMinder Console (main page), click '''Add New Monitor'''. Click the '''Source''' tab. Verify the settings match what you saw with <tt>xawtv</tt>:
; Device Path : <tt>/dev/video0</tt> (or <tt>/dev/v4l/video0</tt>)
; Device Channel : <tt>1</tt> (Composite1)
; Device Format : <tt>PAL</tt> (NTSC in America)
; Capture Palette : <tt>RGB24</tt>
; Capture Width (pixels) : <tt>384</tt>
; Capture Height (pixels) : <tt>288</tt>
; Orientation : <tt>Normal</tt>

When you click ''Save'', your new Monitor's ''Source'' column should be coloured '''''Orange or Green'''''. If it is Red, you probably need to adjust the Width/Height of the captured image.
----
'''For more info, see the [http://www.linuxtv.org/v4lwiki/index.php/Leadtek_WinFast_2000 Video4Linux Wiki]'''