Airlink 101 - Revision history

Kmrs75: /* AICN1620W */

2012-01-27T17:31:11Z

AICN1620W

← Older revision		Revision as of 13:31, 27 January 2012
Line 68:		Line 68:
	<IP_ADDRESS>/cgi/mjpg/mjpg.cgi		<IP_ADDRESS>/cgi/mjpg/mjpg.cgi


	~~I have tried these settings but unable to make this work as of 1-27-12~~

	Remote Protocol: HTTP		Remote Protocol: HTTP
Line 83:		Line 81:
	Remote Image colors: 24 bit		Remote Image colors: 24 bit

	Capture Width: ~~640~~		Capture Width: 320

			Capture Height: 240

			you also have to change a setting in the camera setup>video>mpeg4>QVGA and setup>video>mjpeg>QVGA

	~~Capture Height: 480~~		For Zoneminder this will work but I wouldnt recommend. There is a very long lag time before the camera sees an image and it is shown on Zoneminder. It has taken up too 1 minute before i have seen change in the camera feed.

Kmrs75: /* AICN1620W */

2012-01-27T17:00:44Z

AICN1620W

← Older revision		Revision as of 13:00, 27 January 2012
Line 68:		Line 68:
	<IP_ADDRESS>/cgi/mjpg/mjpg.cgi		<IP_ADDRESS>/cgi/mjpg/mjpg.cgi


			I have tried these settings but unable to make this work as of 1-27-12

	Remote Protocol: HTTP		Remote Protocol: HTTP

Kmrs75: /* AICN1620W */

2012-01-27T16:36:10Z

AICN1620W

← Older revision		Revision as of 12:36, 27 January 2012
Line 59:		Line 59:


	== AICN1620W ==		== AICN1620W ==

	~~Same Camera as Fitivision CS-130A/CS-131A and TrendNet TV-IP410/TV-IP410W. The 'W'/CS-131A version is wireless. Note: the Trendnet cameras have no built-in IR illumination.~~

	~~The device requires authentication, so you need to provide the Remote Host Name parameter with~~		JPEG stills
	~~hostname = <username>:<password>@~~<~~ip of camera~~>		<IP_ADDRESS>/cgi/jpg/image.cgi
	~~path =~~ /cgi/jpg/image.cgi ~~for JPEG stills, or~~ /cgi/mjpg/mjpg.cgi ~~for MJPEG (MJPEG mode requires firmware v1.0.0-24 or later)~~
			MJPEG
			<IP_ADDRESS>/cgi/mjpg/mjpg.cgi


Line 82:		Line 83:
	Capture Width: 640		Capture Width: 640

	Capture Height: 480		Capture Height: 480
	*[http://www.zoneminder.com/forums/viewtopic.php?t=12271 SkyIPCam 7xx PTZ module for ZM and example audio push/dump scripts]
	*[http://www.zoneminder.com/forums/viewtopic.php?t=12238 Additional info on the AirLink SkyIPCam 747W]

Kmrs75: /* Airlink Skyipcam777w */

2012-01-27T16:34:06Z

Airlink Skyipcam777w

← Older revision		Revision as of 12:34, 27 January 2012
Line 57:		Line 57:
	[[Category:Cameras]]		[[Category:Cameras]]
	[[Category:Network Cameras]]		[[Category:Network Cameras]]


			== AICN1620W ==

			Same Camera as Fitivision CS-130A/CS-131A and TrendNet TV-IP410/TV-IP410W. The 'W'/CS-131A version is wireless. Note: the Trendnet cameras have no built-in IR illumination.

			The device requires authentication, so you need to provide the Remote Host Name parameter with
			hostname = <username>:<password>@<ip of camera>
			path = /cgi/jpg/image.cgi for JPEG stills, or /cgi/mjpg/mjpg.cgi for MJPEG (MJPEG mode requires firmware v1.0.0-24 or later)


			Remote Protocol: HTTP

			Remote Method: Simple

			Remote Host Name: <username>:<password>@<ip of camera>

			Remote Host Port: 80

			Remote Host Path: /cgi/mjpg/mjpg.cgi

			Remote Image colors: 24 bit

			Capture Width: 640

			Capture Height: 480
			*[http://www.zoneminder.com/forums/viewtopic.php?t=12271 SkyIPCam 7xx PTZ module for ZM and example audio push/dump scripts]
			*[http://www.zoneminder.com/forums/viewtopic.php?t=12238 Additional info on the AirLink SkyIPCam 747W]

Joymonkey: added page to the 'Network Cameras' category

2011-03-16T19:29:28Z

added page to the 'Network Cameras' category

← Older revision		Revision as of 15:29, 16 March 2011
Line 56:		Line 56:

	[[Category:Cameras]]		[[Category:Cameras]]
			[[Category:Network Cameras]]

MrEvoMan: /* AIC250W */

2010-11-22T15:12:02Z

AIC250W

← Older revision		Revision as of 11:12, 22 November 2010
Line 1:		Line 1:
	== AIC250W ==		== AIC250W ==

	Airlink101 AIC250 settings for 2 fps as JPG stream: to use this camera with Zoneminder with JPG stream, use these settings for the Monitor: "hostname = <ip of camera>", "path = /~~video~~.jpg", use these settings for Options: "ffmpeg" as encoder, "jpg" stream and not mpeg. Select the right resolution for the camera, such as 640x480. To set the resolution for the camera, use a web browser and go to the configuration pages http://<ip of camera>. While in the configuration pages, delete the username and password to get the camera to work with these settings. Save the camera configuration.		Airlink101 AIC250 settings for 2 fps as JPG stream: to use this camera with Zoneminder with JPG stream, use these settings for the Monitor: "hostname = <ip of camera>", "path = /image.jpg", use these settings for Options: "ffmpeg" as encoder, "jpg" stream and not mpeg. Select the right resolution for the camera, such as 640x480. To set the resolution for the camera, use a web browser and go to the configuration pages http://<ip of camera>. While in the configuration pages, delete the username and password to get the camera to work with these settings. Save the camera configuration.

	AIC250W - Just remember to turn off PCRE processing in the Options > Network tab. http://x.x.x.x/video.cgi gives 10 fps 640 x 480 mjpeg feed. Same camera as D-Link DCS-900W / TrendNet IP-200		AIC250W - Just remember to turn off PCRE processing in the Options > Network tab. http://x.x.x.x/video.cgi gives 10 fps 640 x 480 mjpeg feed. Same camera as D-Link DCS-900W / TrendNet IP-200


	== AICN747/AICN747W (Airlink101 SkyIPCam 747W) ==		== AICN747/AICN747W (Airlink101 SkyIPCam 747W) ==

Setarcos: Reordering page details, minor link and info tweaks

2010-03-28T08:18:36Z

Reordering page details, minor link and info tweaks

← Older revision		Revision as of 04:18, 28 March 2010
Line 1:		Line 1:
	== ~~Airlink Skyipcam777w~~ ==		== AIC250W ==

			Airlink101 AIC250 settings for 2 fps as JPG stream: to use this camera with Zoneminder with JPG stream, use these settings for the Monitor: "hostname = <ip of camera>", "path = /video.jpg", use these settings for Options: "ffmpeg" as encoder, "jpg" stream and not mpeg. Select the right resolution for the camera, such as 640x480. To set the resolution for the camera, use a web browser and go to the configuration pages http://<ip of camera>. While in the configuration pages, delete the username and password to get the camera to work with these settings. Save the camera configuration.

			AIC250W - Just remember to turn off PCRE processing in the Options > Network tab. http://x.x.x.x/video.cgi gives 10 fps 640 x 480 mjpeg feed. Same camera as D-Link DCS-900W / TrendNet IP-200


			== AICN747/AICN747W (Airlink101 SkyIPCam 747W) ==

			Same Camera as Fitivision CS-130A/CS-131A and TrendNet TV-IP410/TV-IP410W. The 'W'/CS-131A version is wireless. Note: the Trendnet cameras have no built-in IR illumination.

			The device requires authentication, so you need to provide the Remote Host Name parameter with
			hostname = <username>:<password>@<ip of camera>
			path = /cgi/jpg/image.cgi for JPEG stills, or /cgi/mjpg/mjpg.cgi for MJPEG (MJPEG mode requires firmware v1.0.0-24 or later)


	Remote Protocol: HTTP		Remote Protocol: HTTP
Line 5:		Line 19:
	Remote Method: Simple		Remote Method: Simple

	Remote Host Name: {username}:{password}@{camera ~~ip}~~		Remote Host Name: <username>:<password>@<ip of camera>

	Remote Host Port: 80		Remote Host Port: 80
Line 15:		Line 29:
	Capture Width: 640		Capture Width: 640

	Capture Height: 480		Capture Height: 480
			*[http://www.zoneminder.com/forums/viewtopic.php?t=12271 SkyIPCam 7xx PTZ module for ZM and example audio push/dump scripts]
			*[http://www.zoneminder.com/forums/viewtopic.php?t=12238 Additional info on the AirLink SkyIPCam 747W]

	~~http://www.zoneminder.com/forums/viewtopic.php?t=14094~~

	== ~~AIC250W~~ ==		== Airlink Skyipcam777w ==

	~~Airlink101 AIC250 settings for 2 fps as JPG stream~~: to use this camera with Zoneminder with JPG stream, use these settings for the Monitor: "hostname = <ip of camera>", "path = /video.jpg", use these settings for Options: "ffmpeg" as encoder, "jpg" stream and not mpeg. Select the right resolution for the camera, such as 640x480. To set the resolution for the camera, use a web browser and go to the configuration pages http://<ip of camera>. While in the configuration pages, delete the username and password to get the camera to work with these settings. Save the camera configuration.		Remote Protocol: HTTP

	~~AIC250W - Just remember to turn off PCRE processing in the Options > Network tab. http~~:~~//x.x.x.x/video.cgi gives 10 fps 640 x 480 mjpeg feed. Same camera as D-Link DCS-900W / TrendNet IP-200~~		Remote Method: Simple

			Remote Host Name: {username}:{password}@{camera ip}

	~~Airlink101 SkyIPCam 747W~~		Remote Host Port: 80
	~~The device requires authentication, so you need to provide the~~ Remote Host ~~Name parameter with <username>~~:~~<password>@mycamip~~

	/cgi/~~jpg~~/~~image~~.cgi		Remote Host Path: /cgi/mjpg/mjpg.cgi

	~~http~~:~~//www.zoneminder.com/forums/viewtopic.php?t=12238&highlight=cameras~~		Remote Image colors: 24 bit

	~~== AICN747/AICN747W ==~~		Capture Width: 640

	~~Same Camera as Fitivision CS-130A/CS-131A and TrendNet TV-IP410/TV-IP410W. The 'W'/CS-131A version is wireless. Note~~: ~~the Trendnet cameras have no built-in IR illumination.~~		Capture Height: 480

	~~hostname = <username>:<password>@<ip of camera>~~
	~~path = /cgi/jpg/image.cgi for JPEG stills, or /cgi/mjpg/mjpg.cgi for MJPEG (MJPEG mode requires firmware v1.0.0-24 or later)~~

	~~PTZ module details:~~ [http://www.zoneminder.com/forums/viewtopic.php?t=~~12271 SkyIPCam 7xx ZM Module and Audio dump script~~]		*[http://www.zoneminder.com/forums/viewtopic.php?t=14094 Additional info on the 777W]

	~~[http://www.zoneminder.com/forums/viewtopic.php?t=12238 Additional info on the AirLink SkyIPCam 747W]~~

	[[Category:Cameras]]		[[Category:Cameras]]

Setarcos: /* AICN747/AICN747W */ Updated references to MJPEG support in v1.0.0-24 firmware

2010-03-26T23:59:46Z

AICN747/AICN747W: Updated references to MJPEG support in v1.0.0-24 firmware

← Older revision		Revision as of 19:59, 26 March 2010
Line 39:		Line 39:

	hostname = <username>:<password>@<ip of camera>		hostname = <username>:<password>@<ip of camera>
	path = /cgi/jpg/image.cgi for JPEG stills, or /cgi/mjpg/~~mjpeg~~.cgi for MJPEG (MJPEG mode ~~doesn't return the correct MIME type, and thus doesn't appear to work with ZM~~)		path = /cgi/jpg/image.cgi for JPEG stills, or /cgi/mjpg/mjpg.cgi for MJPEG (MJPEG mode requires firmware v1.0.0-24 or later)

	PTZ module details: [http://www.zoneminder.com/forums/viewtopic.php?t=12271 SkyIPCam 7xx ZM Module and Audio dump script]		PTZ module details: [http://www.zoneminder.com/forums/viewtopic.php?t=12271 SkyIPCam 7xx ZM Module and Audio dump script]

Kingofkya: /* Airlink Skyipcam777w */

2009-09-08T19:34:54Z

Airlink Skyipcam777w

← Older revision		Revision as of 15:34, 8 September 2009
Line 2:		Line 2:

	Remote Protocol: HTTP		Remote Protocol: HTTP

	Remote Method: Simple		Remote Method: Simple

	Remote Host Name: {username}:{password}@{camera ip}		Remote Host Name: {username}:{password}@{camera ip}

	Remote Host Port: 80		Remote Host Port: 80

	Remote Host Path: /cgi/mjpg/mjpg.cgi		Remote Host Path: /cgi/mjpg/mjpg.cgi

	Remote Image colors: 24 bit		Remote Image colors: 24 bit

	Capture Width: 640		Capture Width: 640

	Capture Height: 480		Capture Height: 480


	http://www.zoneminder.com/forums/viewtopic.php?t=14094		http://www.zoneminder.com/forums/viewtopic.php?t=14094


	== AIC250W ==		== AIC250W ==

Kingofkya at 19:34, 8 September 2009

2009-09-08T19:34:08Z

← Older revision		Revision as of 15:34, 8 September 2009
Line 1:		Line 1:
			== Airlink Skyipcam777w ==

			Remote Protocol: HTTP
			Remote Method: Simple
			Remote Host Name: {username}:{password}@{camera ip}
			Remote Host Port: 80
			Remote Host Path: /cgi/mjpg/mjpg.cgi
			Remote Image colors: 24 bit
			Capture Width: 640
			Capture Height: 480

			http://www.zoneminder.com/forums/viewtopic.php?t=14094


	== AIC250W ==		== AIC250W ==