D-Link - Revision history

Opoplawski: DCS-4603

2023-12-08T21:31:00Z

DCS-4603

← Older revision		Revision as of 17:31, 8 December 2023
Line 281:		Line 281:

	ZoneMinder 1.29.0 (Haven't tried earlier versions)		ZoneMinder 1.29.0 (Haven't tried earlier versions)

			=DCS-4603=

			[[Image:DCS-4603.png\|DCS4603]]

			Looked at the HTML source for http://<IP Address of Camera>/index.html and vars.js to determine URLs. There should also be a live2.sdp feed as the video setup page has two video profiles.


			Source Type: Ffmpeg
			Source path: rtsp://user:pass@<IP Address of Camera>/live1.sdp
			Source Method: TCP
			Target colorspace: 24 bit colour
			Capture Resolution: 1440x1080
			Orientation: Normal
			Deinterlacing: Disabled

			Also tried path of http:://user:pass@<IP Address of Camera>/video1.mjpeg but it seemed to be limited to 1 frame per second.

			ZoneMinder 1.36.33 (Haven't tried earlier versions)

	=DCS-5010L, DCS-5020L and DCS-5025L=		=DCS-5010L, DCS-5020L and DCS-5025L=

Iconnor: Remove colors, as 24bit is not recommended and is not relevant.

2022-11-02T13:52:31Z

Remove colors, as 24bit is not recommended and is not relevant.

← Older revision		Revision as of 09:52, 2 November 2022
Line 301:		Line 301:
	Remote Host Port: 80 (Default)		Remote Host Port: 80 (Default)
	Remote Host Path: /video.cgi		Remote Host Path: /video.cgi
	~~Colors: 24 bit~~
	Capture width: 640 (1280 for DCS-5025)		Capture width: 640 (1280 for DCS-5025)
	Capture Height: 480 (720 for DCS-5025)		Capture Height: 480 (720 for DCS-5025)

Iconnor: Remove colors as it is not relevant

2022-11-02T13:51:14Z

Remove colors as it is not relevant

← Older revision		Revision as of 09:51, 2 November 2022
Line 277:		Line 277:
	Remote Host Port: 80 (Default)		Remote Host Port: 80 (Default)
	Remote Host Path: /video1.mjpg		Remote Host Path: /video1.mjpg
	~~Colors: 24 bit~~
	Capture width: 1920		Capture width: 1920
	Capture Height: 1080		Capture Height: 1080

Iconnor: Remove discussion of shm as it is not relevant

2022-11-02T13:49:54Z

Remove discussion of shm as it is not relevant

← Older revision		Revision as of 09:49, 2 November 2022
Line 104:		Line 104:

	For 320x240 motion JPEG, substitute profileid=3. The profile IDs are configurable under the "Audio and Video" setup screen in the camera's built-in web server.		For 320x240 motion JPEG, substitute profileid=3. The profile IDs are configurable under the "Audio and Video" setup screen in the camera's built-in web server.

	~~If the Zoneminder (1.25) monitor crashes every 10-30s (check your logs), set:~~

	~~echo 536870912 >/proc/sys/kernel/shmmax~~

	~~from the wiki [[FAQ#What_does_a_.27Can.27t_shmget:_Invalid_argument.27_error_in_my_logs_mean.3F_and_my_cameras_won.27t_display_video_at_higher_resolutions.]]~~

	=DCS-1100=		=DCS-1100=

Iconnor: Remove colors, as 24bit is not recommended and is not relevant.

2022-11-02T13:48:51Z

Remove colors, as 24bit is not recommended and is not relevant.

← Older revision		Revision as of 09:48, 2 November 2022
Line 80:		Line 80:
	Remote Host Port: 80 (Default)		Remote Host Port: 80 (Default)
	Remote Host Path: /video.cgi		Remote Host Path: /video.cgi
	~~Colors: 24 bit~~
	Capture width: 640		Capture width: 640
	Capture Height: 480		Capture Height: 480

Father1e: /* DCS-8000LH */

2018-06-28T21:13:11Z

DCS-8000LH

← Older revision		Revision as of 17:13, 28 June 2018
Line 596:		Line 596:

	CAUTION: user reported potential issues with newer firmware. Read post.		CAUTION: user reported potential issues with newer firmware. Read post.

			For newer firmware use these settings:
			<pre>
			Source Type: Ffmpeg
			Source Path: http://username:password@<IP Address>/video/flv.cgi
			Remote Method: TCP
			Capture Width: 1280
			Capture Height: 720
			</pre>

	=Incompatible Hardware=		=Incompatible Hardware=

Snake: /* DCS-8000LH */

2018-03-17T16:39:14Z

DCS-8000LH

← Older revision		Revision as of 12:39, 17 March 2018
Line 558:		Line 558:

	=DCS-8000LH=		=DCS-8000LH=

			From the forums:

	So I found a way to get mjpeg from this camera (720p @ ~8fps)		So I found a way to get mjpeg from this camera (720p @ ~8fps)
Line 591:		Line 593:
	Default username is "admin" and the password is the PW that you set		Default username is "admin" and the password is the PW that you set

	~~From~~ [https://forums.zoneminder.com/viewtopic.php?f=14&p=104403 ~~the forum~~]		Forum [https://forums.zoneminder.com/viewtopic.php?f=14&p=104403 post]


			CAUTION: user reported potential issues with newer firmware. Read post.

	=Incompatible Hardware=		=Incompatible Hardware=

Snake at 17:34, 2 February 2018

2018-02-02T17:34:41Z

← Older revision		Revision as of 13:34, 2 February 2018
Line 558:		Line 558:

	=DCS-8000LH=		=DCS-8000LH=

	~~From [https://forums.zoneminder.com/viewtopic.php?f=14&p=104403 the forum]:~~

	So I found a way to get mjpeg from this camera (720p @ ~8fps)		So I found a way to get mjpeg from this camera (720p @ ~8fps)
Line 568:		Line 566:
	I had to configure one of the stream profiles to output MJPEG rather than h.264 (until I can find a way to get ZM to read H.264 over port 80):		I had to configure one of the stream profiles to output MJPEG rather than h.264 (until I can find a way to get ZM to read H.264 over port 80):
	Send a request to the following URL:		Send a request to the following URL:

	<IP ADDRESS>/config/video.cgi?profileid=1&codec=MJPEG		<IP ADDRESS>/config/video.cgi?profileid=1&codec=MJPEG

	you'll need to authenticate with the username "admin" and the password you set when configuring the cam.		you'll need to authenticate with the username "admin" and the password you set when configuring the cam.
	You can either do this in a web browser, or in CURL or WGET. You should also be able to do it in invoke-webrequest, but why?		You can either do this in a web browser, or in CURL or WGET. You should also be able to do it in invoke-webrequest, but why?
Line 575:		Line 575:

	You can then immediately retrieve an mjpeg stream from:		You can then immediately retrieve an mjpeg stream from:

	<IP ADDRESS>/video/mjpg.cgi		<IP ADDRESS>/video/mjpg.cgi

	Configure Zoneminder with:		Configure Zoneminder with:
			<pre>
	Source Type: remote		Source Type: remote
	Remote ~~protocol~~: HTTP		Remote Protocol: HTTP
	~~remote method~~: Simple		Remote Method: Simple
	~~remote host name~~: username:password@<IP ADDRESS>		Remote Hostname: username:password@<IP ADDRESS>
	~~remote host~~ Port: 80		Remote Host Port: 80
	~~remote host path~~: /video/mjpg.cgi		Remote Host Path: /video/mjpg.cgi
	~~width~~: 1280		Width: 1280
	~~height~~: 720		Height: 720
			</pre>
			Default username is "admin" and the password is the PW that you set

	~~Default username is "admin" and~~ the ~~password is the PW that you set~~		From [https://forums.zoneminder.com/viewtopic.php?f=14&p=104403 the forum]

Snake at 17:29, 2 February 2018

2018-02-02T17:29:11Z

← Older revision		Revision as of 13:29, 2 February 2018
Line 557:		Line 557:
	</pre>		</pre>

	=DCS-~~800LH~~=		=DCS-8000LH=

	From [https://forums.zoneminder.com/viewtopic.php?f=14&p=104403 the forum]:		From [https://forums.zoneminder.com/viewtopic.php?f=14&p=104403 the forum]:

Snake at 17:28, 2 February 2018

2018-02-02T17:28:30Z

@@ Line 556: / Line 556: @@
 * rtsp://<cam-ip>:554/live.sdp // feeds VLC
 </pre>
 =Incompatible Hardware=