Foscam FI9821W V2 - Revision history

Doisneau at 10:20, 7 March 2020

2020-03-07T10:20:16Z

← Older revision		Revision as of 06:20, 7 March 2020
Line 31:		Line 31:

	Note 2 addendum: I was only able to PTZ working if Control Device was in the format of user:password		Note 2 addendum: I was only able to PTZ working if Control Device was in the format of user:password

			=== Resolution ===

	You should be able to use higher or lower resolutions but keep the WidthxHeight ratio within the values you did set in the Camera settings.		You should be able to use higher or lower resolutions but keep the WidthxHeight ratio within the values you did set in the Camera settings.

			If those settings are not equal, your ZM logs will complain: <code>Monitor dimensions are 640x400 but camera is sending 1280x720</code>

Doisneau: Camera resolution should reflect what has been set into the camera itself

2020-03-07T10:17:52Z

Camera resolution should reflect what has been set into the camera itself

← Older revision		Revision as of 06:17, 7 March 2020
Line 18:		Line 18:
	* Source Path: rtsp://admin:(Password)@IP-Address:88/videoMain		* Source Path: rtsp://admin:(Password)@IP-Address:88/videoMain
	* Remote Method: RTP/Unicast		* Remote Method: RTP/Unicast
	* Capture ~~Width~~: ~~640~~		* Capture Resolution (pixels): <code>1280x720 720p</code> preset
	* Capture Height: 320
	* Control Type: Foscam FI9821W (see note 1)		* Control Type: Foscam FI9821W (see note 1)
	* Control Device: (Password) (see note 2)		* Control Device: (Password) (see note 2)
Line 33:		Line 32:
	Note 2 addendum: I was only able to PTZ working if Control Device was in the format of user:password		Note 2 addendum: I was only able to PTZ working if Control Device was in the format of user:password

	You should be able to use higher or lower resolutions but keep the WidthxHeight ratio within the ~~640x320 value~~		You should be able to use higher or lower resolutions but keep the WidthxHeight ratio within the values you did set in the Camera settings.

Doisneau: basic formatting

2020-03-07T10:09:49Z

basic formatting

@@ Line 1: / Line 1: @@
-Foscam FI9821W V2 with control
+= Foscam FI9821W V2 with control =
 With the newer version of the Foscam firmware you are prompted to change the default login. I did this then added another user called admin. I'm not sure if this is necessary but I was able to get the camera to work with control.
-Camera Video Settings:
+== Camera Video Settings ==
-Stream Type        HD Mode
+* Stream Type: HD Mode
-Resolution         720P
+== Zoneminder Monitor Settings ==
-Bit Rate           128K
+* Source Type: Ffmpeg
-Frame Rate         5
+== Notes ==
 Note 1: Edit Foscam FI9821W and remove check marks in Zoom, Focus, White, Iris, and change Presets number from 16 to 8
 Note 2: You may be able to use just the camera password or user=(user)&pwd=(password)
 Note 2 addendum: I was only able to PTZ working if Control Device was in the format of user:password
 You should be able to use higher or lower resolutions but keep the WidthxHeight ratio within the 640x320 value

Marcjw at 22:23, 15 February 2016

2016-02-15T22:23:55Z

← Older revision		Revision as of 18:23, 15 February 2016
Line 43:		Line 43:

	Note 2: You may be able to use just the camera password or user=(user)&pwd=(password)		Note 2: You may be able to use just the camera password or user=(user)&pwd=(password)
			Note 2 addendum: I was only able to PTZ working if Control Device was in the format of user:password

	You should be able to use higher or lower resolutions but keep the WidthxHeight ratio within the 640x320 value		You should be able to use higher or lower resolutions but keep the WidthxHeight ratio within the 640x320 value

Bbunge at 18:42, 9 September 2015

2015-09-09T18:42:17Z

← Older revision		Revision as of 14:42, 9 September 2015
Line 3:		Line 3:
	With the newer version of the Foscam firmware you are prompted to change the default login. I did this then added another user called admin. I'm not sure if this is necessary but I was able to get the camera to work with control.		With the newer version of the Foscam firmware you are prompted to change the default login. I did this then added another user called admin. I'm not sure if this is necessary but I was able to get the camera to work with control.

	Camera Video Settings:		Camera Video Settings:

	Stream Type HD Mode		Stream Type HD Mode

	Resolution 720P		Resolution 720P

	Bit Rate 128K		Bit Rate 128K

	Frame Rate 5		Frame Rate 5

	Key Frame Interval 50		Key Frame Interval 50

	Variable bitrate Yes		Variable bitrate Yes


	Zoneminder Monitor Settings:		Zoneminder Monitor Settings:

	Source Type Ffmpeg		Source Type Ffmpeg

	Function Modect (or your choice)		Function Modect (or your choice)

	Source Path rtsp://admin:(Password)@IP-Address:88/videoMain		Source Path rtsp://admin:(Password)@IP-Address:88/videoMain

	Remote Method RTP/Unicast		Remote Method RTP/Unicast

	Capture Width 640		Capture Width 640

	Capture Height 320		Capture Height 320

	Control Type Foscam FI9821W (see note 1)		Control Type Foscam FI9821W (see note 1)

	Control Device (Password) (see note 2)		Control Device (Password) (see note 2)

	Control Address IP-Address:88		Control Address IP-Address:88

	Auto Stop Timeout 1		Auto Stop Timeout 1

Bbunge: Created page with "Foscam FI9821W V2 with control With the newer version of the Foscam firmware you are prompted to change the default login. I did this then added another user called admin. I'..."

2015-09-09T18:41:12Z

Created page with "Foscam FI9821W V2 with control With the newer version of the Foscam firmware you are prompted to change the default login. I did this then added another user called admin. I'..."

New page

Foscam FI9821W V2 with control

With the newer version of the Foscam firmware you are prompted to change the default login. I did this then added another user called admin. I'm not sure if this is necessary but I was able to get the camera to work with control.

Camera Video Settings:
Stream Type HD Mode
Resolution 720P
Bit Rate 128K
Frame Rate 5
Key Frame Interval 50
Variable bitrate Yes

Zoneminder Monitor Settings:
Source Type Ffmpeg
Function Modect (or your choice)
Source Path rtsp://admin:(Password)@IP-Address:88/videoMain
Remote Method RTP/Unicast
Capture Width 640
Capture Height 320
Control Type Foscam FI9821W (see note 1)
Control Device (Password) (see note 2)
Control Address IP-Address:88
Auto Stop Timeout 1

Note 1: Edit Foscam FI9821W and remove check marks in Zoom, Focus, White, Iris, and change Presets number from 16 to 8

Note 2: You may be able to use just the camera password or user=(user)&pwd=(password)

You should be able to use higher or lower resolutions but keep the WidthxHeight ratio within the 640x320 value