Loftek - Revision history

Jcs: Syslog messages

2012-04-06T22:43:51Z

Syslog messages

← Older revision		Revision as of 18:43, 6 April 2012
Line 12:		Line 12:
	This is an outdoor fixed-mount camera with wifi capabilities. This camera can be configured by following the instructions under "Create the Monitor", but not the instructions under "PTZ Control".		This is an outdoor fixed-mount camera with wifi capabilities. This camera can be configured by following the instructions under "Create the Monitor", but not the instructions under "PTZ Control".

	Use of this camera with Zoneminder will cause the syslog to be flooded with "Corrupt JPEG data" messages. This is annoying, but the messages are apparently harmless.		Use of this camera with Zoneminder will cause the syslog to be flooded with "Corrupt JPEG data" messages. This is annoying, but the messages are apparently harmless, as the images are captured correctly and without any visible corruption.

	== Create the Monitor ==		== Create the Monitor ==

2012-04-06T22:43:18Z

Syslog messages

← Older revision		Revision as of 18:43, 6 April 2012
Line 11:		Line 11:

	This is an outdoor fixed-mount camera with wifi capabilities. This camera can be configured by following the instructions under "Create the Monitor", but not the instructions under "PTZ Control".		This is an outdoor fixed-mount camera with wifi capabilities. This camera can be configured by following the instructions under "Create the Monitor", but not the instructions under "PTZ Control".

			Use of this camera with Zoneminder will cause the syslog to be flooded with "Corrupt JPEG data" messages. This is annoying, but the messages are apparently harmless.

	== Create the Monitor ==		== Create the Monitor ==

2012-04-06T22:40:26Z

Nexus 543

← Older revision		Revision as of 18:40, 6 April 2012
Line 7:		Line 7:
	<br/>		<br/>
	<br/>		<br/>

			== Loftek Nexus 543 ==

			This is an outdoor fixed-mount camera with wifi capabilities. This camera can be configured by following the instructions under "Create the Monitor", but not the instructions under "PTZ Control".

	== Create the Monitor ==		== Create the Monitor ==

2012-01-29T17:08:49Z

Notes & Troubleshooting

← Older revision		Revision as of 13:08, 29 January 2012
Line 529:		Line 529:
	== Notes & Troubleshooting ==		== Notes & Troubleshooting ==
	# The PTZ Control File is compatible with Zoneminder 1.25.0. If using an older version, you may have to change the line that reads "use ZoneMinder::Logger qw(:all);" to "use ZoneMinder::Debug qw(:all);" .		# The PTZ Control File is compatible with Zoneminder 1.25.0. If using an older version, you may have to change the line that reads "use ZoneMinder::Logger qw(:all);" to "use ZoneMinder::Debug qw(:all);" .
			# If the Control tab is not visible in the Monitor configuration window then verify that OPT_CONTROL is enabled under the Options -> System Tab.
	# '''TODO''': Add more notes		# '''TODO''': Add more notes


	== References ==		== References ==

2012-01-29T17:05:23Z

Create the Monitor

← Older revision		Revision as of 13:05, 29 January 2012
Line 29:		Line 29:
	:Capture Height: 480		:Capture Height: 480

	This will give you a 640x480 video stream running at ~5 fps. Refer to the table on the [[Foscam]]~~Foscam~~ page ''[1]'' for other frame rate settings.		This will give you a 640x480 video stream running at ~5 fps. Refer to the table on the [[Foscam]] page ''[1]'' for other frame rate settings.
	Unlike the Foscam's , I have not run into any issues running at 640x80.		Unlike the Foscam's , I have not run into any issues running at 640x80.

2012-01-29T17:05:05Z

Create the Monitor

← Older revision		Revision as of 13:05, 29 January 2012
Line 29:		Line 29:
	:Capture Height: 480		:Capture Height: 480

	This will give you a 640x480 video stream running at ~5 fps. Refer to the table on the Foscam page ''[1]'' for other frame rate settings.		This will give you a 640x480 video stream running at ~5 fps. Refer to the table on the [[Foscam]]Foscam page ''[1]'' for other frame rate settings.
	Unlike the Foscam's , I have not run into any issues running at 640x80.		Unlike the Foscam's , I have not run into any issues running at 640x80.

2012-01-29T17:03:34Z

← Older revision		Revision as of 13:03, 29 January 2012
Line 1:		Line 1:
	~~NOTE: This is my first attempt at creating a Wiki page. Please excuse the formatting (or lack thereof) as I go through my learning curve.~~

	~~'''TODO''': Add Photo of camera~~

	== Loftek Sentinel ==		== Loftek Sentinel ==
	[[File:Loftek_ptz.jpg\|200px\|right]]		[[File:Loftek_ptz.jpg\|200px\|right]]

2012-01-29T17:02:54Z

PTZ Control

← Older revision		Revision as of 13:02, 29 January 2012
Line 518:		Line 518:
	When finished, click the "Save" button.		When finished, click the "Save" button.

	~~'''INCOMPLETE~~:~~''' Finish instructions~~		Now go back to the Monitor configuration window, click on the "Control" tab and enter the following:

	;Control:		;Control:
Line 526:		Line 526:
	:Control Address: admin:{password}@{camera ip address}		:Control Address: admin:{password}@{camera ip address}
	:Auto Stop Timeout: 0.50 (or whatever works best for you)		:Auto Stop Timeout: 0.50 (or whatever works best for you)

			When finished, click the "Save" button.

			At this point you should have a working PTZ camera. Try it out and verify everything works as expected.

	== Notes & Troubleshooting ==		== Notes & Troubleshooting ==

2012-01-29T17:00:33Z

PTZ Control

← Older revision		Revision as of 13:00, 29 January 2012
Line 474:		Line 474:
	</pre>		</pre>

	Once the PTZ control file has been saved, open the Monitor created previously and click on the "Control" tab. Next click on "Edit" and then "Add New Control". Enter the following information at each tab:		Once the PTZ control file has been saved, open the Monitor created previously and click on the "Control" tab. Next click on "Edit" and then the "Add New Control" button. Enter the following information at each tab:

	;Main:		;Main:

2012-01-29T16:59:51Z

PTZ Control

@@ Line 476: / Line 476: @@
 Once the PTZ control file has been saved, open the Monitor created previously and click on the "Control" tab. Next click on "Edit" and then "Add New Control". Enter the following information at each tab:
-;Main: Loftek Sentinel
+;Main:
-:Name: Tick
+:Name: Loftek Sentinel
 :Type: Remote
 :Protocol: LoftekSentinel (notice no space)
 :Can reset: Tick
 '''INCOMPLETE:''' Finish instructions