Hikvision

Models

• Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet

• Hikvision DS-2CD2732F-I(S) Megapixel Outdoor IP Dome Camera

• Hikvision DS-2CD2532F-IWS 3MP Outdoor IP Mini Dome Camera

• Hikvision DS-2CD2012-I 1.3MP IR Mini Bullet Camera

• Hikvision DS-2CD2332-I 3MP Outdoor Network Mini Dome Camera

• Hikvision DS-2CD2022WD-I

• Hikvision DS-2CD2025FWD-i 1920x1080 30FPS Bullet

• Hikvision DS-2CD2142FWD-I 4MP Mini Vandal Dome IP Camera PoE

• Hikvision DS-7204-7208-7216HVI-ST‎‎ IP Video Encoder DVR - Supports HD-TVI, Analog, and IP Cameras (has errors)

• Hikvision Video Doorbell DS-KB6003-WIP

• Hikvision DS-2DE2A404IW-DE3

• Hikvision DT2A404

• Hikvision DS-2CD2532F-IS

For the DS-2CD2032-I model, see the the DS-2CD2332-I model.

About

These seem to work. The biggest problem is people trying to use 'network camera' instead of 'ffmpeg' source type. Both have rtsp but only ffmpeg works here (because of h.264?) see [[1]]

Model	Comment
DS-2CD2055FWD-I bullet	Works with ZM 1.30.4 with Ffmpeg
DS-2CD2632F-IS Update Version outdoor bullet	Works with ZM 1.30.4 ONVIF works for fast setup. See Model Specific Wiki page Hikvision DS-2CD1631FWD-I CCTV POE 3MP HD Varifocal IR Bullet
DS-2CD2732F-I	Tested.
DS-2CD2032-I	Tested. The DS-2CD2032-I's come in several different versions (Chinese, Int'l, English, etc...) each with multiple firmwares available. Be sure that you use the correct firmware for your camera model for best results.
DS-2CD2035-I outdoor bullet	Works using Ffmpeg.
DS-2CD2532F-IWS	Tested to work reliably only with Libvlc as source type.
DS-2CD2012-I	Works.
DS-2CD2085FWD-I	Works
DS-2DE3204W-DE	At least pan, tilt and focus (to min. or max.) work in ZM 1.34. Used ffmpeg for capture and HikVision protocol for control.

You can add some flags to the stream. An example is in the forum where ?tcp is added to the end of the stream to reduce artifacts.

Hikvision DS-2DE2A404IW-DE3

The Model Hikvision DT2A404 is a OEM version of the Hikvision DS-2DE2A404IW-DE3 IP after reset is 192.168.1.64

The following configuration is a example that is tested Zoneminder 1.32.3 but is expected to work with other versions, too. The easy way ist to use the ONVIF Probe button in the upper right corner of each "Monitor" window.

In general, use the following configuration:

Config Tab	Option	Config Setting
General	Source Type	Ffmpeg
Source	Source Path	to access the mainstream: rtsp://user:yourpassword@192.168.1.64:554/ch1/main/av_stream example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/main/av_stream or rtsp://user:yourpassword@192.168.1.64:554/Streaming/Channels/101?transportmode=mcast&profile=Profile_1 to access the substream: rtsp://192.168.0.1:554/ch1/sub/av_stream example: rtsp://admin:yourpassword@192.168.1.64:554/ch1/sub/av_stream
	Remote Method	TCP or UDP
	Target Colorspace	32 bit colour
	Capture Width (pixels)	2560
	Capture Height (pixels)	1440
	Preserve Aspect Ratio	Unselected
	Orientation	Normal
	Deinterlacing	Disabled
Control
	Control Type	HikVision
	Control Device (necessary for ptz,enter the exact camera model	DS-2DE2A404IW-DE3
	Control Address	user:yourpassword@192.168.1.64
	within the Hikvision Control Type: Protocol	HikVision

General Tab

Source Type : Ffmpeg / Libvlc / Remote(only some FW revisions)

Source Tab

Source Path : rtsp://<username>:<password>@<ip_address>:<port>/Streaming/Channels/1?tcp

(example: rtsp://admin:12345@mycamera.mydomain.com//Streaming/Channels/1)

Target Colorspace : 24 bit colour

Capture Width (pixels) : 1280 (set these to match camera config)

Capture Height (pixels) : 720

I also had to set max FPS slightly higher than set in camera, or i lost the lower half of the frame. (Camera seems to send 10.6fps when 10 is selected)

The following URL gives another Source path that was far more stable on Zoneminder 1.25: http://onlinetechadvice.blogspot.com/2014/04/hikvision-ds-2cd2032-i-working-in.html#comment-form

The Source path that worked for me is: rtsp://username:password@XXX.XXX.XXX.XXX:554/cam/realmonitor?channel=1&subtype=0?tcp Of course, replace username and password and port with your specific installation information.

The "Remote" option also seems to work now in ZM 1.28 (at least with ds-2cd2032-i's of a certain firmware version), with less rtsp streaming errors than when using ffmpeg. The source path /Streaming/Channels/1 works fine with firmware version 5.1.6, but seems to not work any longer in 5.2.5. The source path /cam/realmonitor?channel=1&subtype=0 works on any firmware model. In ZM 1.28 (perhaps earlier as well), TCP is automatically forced when the "Remote" source type is chosen and RTP/RTSP is used (https://github.com/ZoneMinder/ZoneMinder/issues/323), so the trailing "?tcp" is not necessary for either URL when this configuration is used.

Issues

• It's recommended to use ZM 1.34 (or the most up to date stable (even numbered) branch), as older ZMs may lack compatibility. e.g. 1.30.4 w/ffmpeg will fail, yet 1.34 w/ffmpeg will work with the streams.

See Also

• The forum has multiple posts regarding Hikvision. Search there for more details.