Difference between revisions of "Single Board Computers"
(Added Z83 II AMD64) |
|||
| (10 intermediate revisions by 2 users not shown) | |||
| Line 18: | Line 18: | ||
===As Server=== | ===As Server=== | ||
* [[Raspberry Pi 2 - Fedora]] | * [[Raspberry Pi 2 - Fedora]] | ||
* [https://zoneminder.blogspot.com/p/raspberry-pi-3.html Raspberry Pi 3 - Fedora/Fedberry] | |||
* [[Raspberry Pi - Raspbian]] | |||
* [[Raspberry Pi 2 - Raspbian]] | * [[Raspberry Pi 2 - Raspbian]] | ||
* [[Raspberry Pi | * [[Raspberry Pi 3 - Raspbian]] | ||
* | * Premade image for RPI3b here: https://zmrepo.zoneminder.com | ||
* [ | * [[Raspberry Pi 4 - Raspbian]] - Uses Buster. Applicable to other RPIs that have Buster. | ||
* [[Odroid - XU4 - Ubuntu Mate]] | * [[Odroid - XU4 - Ubuntu Mate]] | ||
| Line 34: | Line 37: | ||
* [[Beaglebone Black - Devuan Jessie]] | * [[Beaglebone Black - Devuan Jessie]] | ||
* Z83 II , Intel Atom X5-Z8350, runs well with 75-85 % Usage @ 10 fps, 4 HD-cams and motion detection | |||
===As Client=== | ===As Client=== | ||
| Line 52: | Line 51: | ||
==General Tips== | ==General Tips== | ||
* Disable all logging | * Disable all logging and any data collection (''RECORD_EVENT_STATS'' - See ''Logging'' tab) on ARM boards if you are running a flash based HD. | ||
If load is high or cameras don't seem to work lower the following: | |||
* Resolution | * Resolution | ||
* FPS | * FPS (on camera only) | ||
* Analysis zone size or change from Mocord to Record. | * Analysis zone size or change from Mocord to Record. | ||
* Limit analysis FPS (motion detection uses the most CPU) | |||
===GPU Memory=== | ===GPU Memory=== | ||
User from the forum reports that adjusting GPU memory will improve RPI4 performance with ZM. | User from the forum reports that adjusting GPU memory will improve RPI4 performance with ZM. | ||
http://forums.zoneminder.com/viewtopic.php?f=39&t=28614&p=113082&hilit=gpu&sid=20dae3382577cc3019eac3b60d3bcfac#p113082 | http://forums.zoneminder.com/viewtopic.php?f=39&t=28614&p=113082&hilit=gpu&sid=20dae3382577cc3019eac3b60d3bcfac#p113082 | ||
'''piflipper''': ''I had the same issue, to solve it I upped the GPU memory to 512MB, via raspi-config and everything started working. Now have 3 cameras working without any issues.'' | |||
http://forums.zoneminder.com/viewtopic.php?f=38&t=28706&p=112388&hilit=gpu&sid=20dae3382577cc3019eac3b60d3bcfac#p112388 | http://forums.zoneminder.com/viewtopic.php?f=38&t=28706&p=112388&hilit=gpu&sid=20dae3382577cc3019eac3b60d3bcfac#p112388 | ||
'''fatboy''': ''Working *great* now! Increase GPU memory: ''/boot/config.txt'' - gpu_mem=512'' | |||
===RPI Image for ZM=== | |||
There is a pre-made RPI image for Zoneminder at https://zmrepo.zoneminder.com | |||
Based on Raspbian Lite, and tested on RPI3b. | |||
Only adjustment needed may be to increase GPU_MEM slightly. | |||
===Hardware h264=== | |||
https://forums.zoneminder.com/viewtopic.php?f=40&t=30565 | |||
==Resources== | ==Resources== | ||
[https://zoneminder.blogspot.com Zoneminder Blogspot] - Notes on Various Single Board Computers | [https://zoneminder.blogspot.com Zoneminder Blogspot] - Notes on Various Single Board Computers | ||
Latest revision as of 02:49, 10 August 2022
The following pages cover Single Board Computers with Zoneminder.
Traditionally, these are ARM based; The Raspberry Pi, The Beaglebone, and others. For those not experienced with ARM these devices perform at level below an x86 based motherboard, yet offer lower power consumption and purchase cost. When using an ARM board, it is recommended to run cameras at lower resolutions (e.g. 640x480 or 800x600), and lower frame rates. Additionally, zones should be smaller, as analysis of motion will use up CPU. Alternatively, you can avoid Modect and Mocord and use Record.
Single Board Computers (ARM) work well for a small home setup, or as an adjunct to a larger camera system. For large camera systems, they are not usually powerful enough.
Usage
There are at least three ways an SBC can be used with ZM (this also applies to any computer...)
- ZM server
- ZM client (viewing ZM and displaying feeds on a monitor)
- Camera (attached via usb or other peripheral)
List
As Server
- Premade image for RPI3b here: https://zmrepo.zoneminder.com
- Raspberry Pi 4 - Raspbian - Uses Buster. Applicable to other RPIs that have Buster.
- Z83 II , Intel Atom X5-Z8350, runs well with 75-85 % Usage @ 10 fps, 4 HD-cams and motion detection
As Client
- Dedicated SBC Camera Monitor Beaglebone w/Devuan Jessie & Firefox
As Camera
General Tips
- Disable all logging and any data collection (RECORD_EVENT_STATS - See Logging tab) on ARM boards if you are running a flash based HD.
If load is high or cameras don't seem to work lower the following:
- Resolution
- FPS (on camera only)
- Analysis zone size or change from Mocord to Record.
- Limit analysis FPS (motion detection uses the most CPU)
GPU Memory
User from the forum reports that adjusting GPU memory will improve RPI4 performance with ZM.
piflipper: I had the same issue, to solve it I upped the GPU memory to 512MB, via raspi-config and everything started working. Now have 3 cameras working without any issues.
fatboy: Working *great* now! Increase GPU memory: /boot/config.txt - gpu_mem=512
RPI Image for ZM
There is a pre-made RPI image for Zoneminder at https://zmrepo.zoneminder.com Based on Raspbian Lite, and tested on RPI3b.
Only adjustment needed may be to increase GPU_MEM slightly.
Hardware h264
https://forums.zoneminder.com/viewtopic.php?f=40&t=30565
Resources
Zoneminder Blogspot - Notes on Various Single Board Computers
