Level One
General information
This camera(s) works fine with zoneminder.
- Remote Host Name: user:password@<ip>
- Remote Host Port: 80 (is default, alternative 1024 when you've setup this port by webconfig)
- Remote Host Path: /img/video.mjpeg
WCS-2003
This camera supports MP4 or MJPEG. Additional to the information above the remote path is different:
- MP4 stream remote path: /img/video.asf
In the Monitor definition window of Zoneminder set following values:
Select as source type: Ffmpeg
Source Path: http://<your_camera_ip>/img/video.asf
Set capture width and capture height according the configuration settings of your camera
- MJPEG stream remote path: /img/mjpeg.jpg (not yet fully tested)
This camera has a Linux based firmware. The source code of the firmware is available at the
Level One WCS-2003 page
file WCS-2003(GPL)_2004-07-28.zip
FCS-1101
This camera supports MPEG4 or MJPEG. I just got MJPEG to work with Zoneminder. I didn't get RTSP (Port 554) and MPEG4 Port 8090 to work with Zoneminder, but it's no problem to access these ports with VLC.
Here are the settings:
- Source type: Remote
- Remote Protocol: HTTP
- Remote Method: Simple
- Remote Hostname: Your Cameras IP
- Remote Hostport: 8070
- Remote Hostpath: /video.mjpg
- Width: Set width depending to the image width you have configured
- Height: Set height depending to the image width you have configured
FCS-5030
This camera is working with Zoneminder.
Here are the settings:
- Source type: Remote
- Remote Protocol: HTTP
- Remote Method: Simple
- Remote Host Name: <USERNAME>:<PASSWORD>@<IP CAMERA> <-- example root:@192.168.1.2
- Remote Host Port: 80
- Remote Host Path: video.mjpg
- Width: Set width depending to the image width you have configured
- Height: Set height depending to the image width you have configured
FCS-5051
Unfortunately at this moment ffmpeg (svn date: 2011-12-21) doesn't support RTSP or MJPEG stream for this camera. Zoneminder works fine with JPG snapshot.
Here are the settings:
- Source type: Remote
- Maximum FPS: 10
- Alarm Maximum FPS: 12
- Remote Protocol: HTTP
- Remote Method: Simple
- Remote Host Name: <USERNAME>:<PASSWORD>@<IP CAMERA> <-- example root:@192.168.1.2
- Remote Host Port: 80
- Remote Host Path: /cgi-bin/jpg/image.cgi?
- Width: Set width depending to the image width you have configured
- Height: Set height depending to the image width you have configured
WCS-0030 (likely also FCS-0030 and perhaps other but not tested)
I got this camera (hardware version 2) to work in RTSP using the following settings:
WCS-0030 configuration:
- Video >> Stream >> Video Codec: MPEG4
- Video >> RTSP Server >> Port: 554
- Video >> RTSP Server >> Authentication: None
Zoneminder:
- Source type: Remote
- Remote Protocol: RTSP
- Remote Method: RTP/Unicast
- Remote Hostname: login:password@YourIP
- Remote Hostport: 554
- Remote Hostpath: /channel1
- Width: Set width depending to the image width you have configured
- Height: Set height depending to the image width you have configured
1280x800@15fps in highest quality works fine.
Other Level One cameras (not tested)
Note: This is not tested, just for infomation.
This information is from here:
Following cameras use URL http://IP-AddressCamera/cdi-bin/video.jpg:
FCS-1010, FCS-1030, FCS-1040, FCS-1060, FCS-1070, FCS-3000, FCS-3021, WCS-2010, WCS-2030, WCS-2040, WCS-2060, WCS-2070
The cameras FCS-0010, FCS-0020, FCS-1091, WCS-0010, WCS-0020, WCS-1090 are supporting MJPG, the URL is
http://IP-address/video.mjpg
For the cameras FCS-1081, FCS-1081A, FCS-4000, FCS-4100, FCS-4200, FCS-4300, FCS-4400, FCS-4500, FCS-7011 the command to get
the actual JPG image is:
http://ip_address_of_camera/cgi-bin/jpg/image and then http://ip_address_of_camera/jpg/image.jpg
or for MJPG http://IPaddresse:port/video.mjpg
The SDK´s for the Level One cameras could be downloaded from:
