Understanding ZoneMinder's Zoning system for Dummies

<Home

Background

ZoneMinder has a flexible (albeit hard to easily configure) zone detection system using which you can modify how sensitive, precise, accurate your motion alarms are. The official ZM documentation does a good job of describing all the concepts here. However, you will see gobs of posts in the forum about people complaining that ZM logs all sorts of events (ahem, as did I), ZM's detection is rubbish and in-camera is better (ahem, as did I) and what not. But once you get the concept, its incredibly powerful.

So instead of giving you a theoretical explanation, lets walk through a live use-case. (Credit: user kkrofft helped a lot in me getting a hang of things here. You should also read his earlier explanation here)

Real object detection

People often ask if ZM supports "object detection". The core ZM engine only detects change in pixels (motion), which is what this article is about. That being said, incase you did not know, ZoneMinder now has support for person, object, face recognition. So while you can and should optimize your zones, if your real interest is person detection, you can do that using my event server. Note that object detection works after ZM detects motion change, so this article applies either way.

Some concepts

Let's take a look at this area below. Lets suppose you want to trigger motion if someone tries to break into your basement. Does it make sense you monitor the full area (pillars/walls/floor)? Probably not. If someone were to break in, they'd break in from some door, some window, or maybe break in from upstairs and climb down the stairs. So doesn't it make more sense to monitor these areas specifically? I think so. So the first 'common sense' logic is delete the default zone that ZM creates for each monitor (which is called All). Monitoring every part of your image may make sense if you are monitoring and outdoor lawn, for example. Not here.

Error creating thumbnail: Unable to save thumbnail to destination

Defining the zone areas

So given the explanation above, how about we define zones where motion matters? Any zone you define as "active" is what ZoneMinder will analyze for motion. Ignore the 'preclusive for now'. So lets look at the image below. I've defined polygons around places that are the "entry points"

Error creating thumbnail: Unable to save thumbnail to destination

Okay, now how do I specify the sensitivity of the zones?

ZoneMinder has pre-sets. We live in a world of pre-sets. I bet you want to select "Best and highly sensitive" don't you? DON'T. Not because that setting is nonsense, but because you should understand some concepts first.

Core Concepts

The ZM wiki I pointed to earlier does a great job of explaining different methods. At the cost of repeating what has already been said, its important to note:

• ZM does NOT understand objects. It only understands pixel colors. So if you are monitoring a camera that is producing a 1280x960 32bit color depth image, as far as ZM is concerned, it is getting an array of 1280*960*32 bits of data to analyze and compare a previous frame and based on 'color differences' between frame X-1 and X along with some algorithms it applies in addition to color differences, it tries and guesses if objects (in ZM speak, a specific pattern of pixels) have come up that were not there previously.

• ZM has 3 methods of detection: Alarmed Pixels, Filtered Pixels and Blobs. Here is a visual explanation of their differences

The first image is a 20x20 grid. Let's assume this is a zone. And the black circle is some object in this grid. The second image shows the next frame of that image, where new 'objects' have appeared, or in ZM's view 'new sets of pixel patterns'

Now let's talk about Alarmed Pixels, Filtered Pixels and Blobs

Error creating thumbnail: Unable to save thumbnail to destination

Error creating thumbnail: Unable to save thumbnail to destination

Alarmed Pixels

Alarmed pixels only deals with pixels changes. If we use the alarmed pixel method and specify a minimum of "5 pixel" changes (lets forget max for now), then all the new pixels of set A + B + C + D will count as alarmed pixels and the total alarmed pixel count will be A+B+C+D

Filtered Pixels

Now let's assume we used Filtered pixels and set it to 2x2 pixels. The in addition to computing the alarmed pixels (A+B+C+D), it will also count how many of these sets have at least 2 pixels around them that are also alarmed pixels. This will result in B+C+D (set A will be discarded as they don't have any pixels surrounded by at least 2 pixels that have changed color from the prev. frame)

Blob Pixels

Now lets assume we used Blob and said a blob needs to be at least 10 pixels. Then what it will do is based on the set computed by Filtered pixels, which is B+C+D it will look for contiguous blobs of 10 pixels and that only means D

So, in Alarmed pixels any of A, B, C or D would raise an alarm In filtered pixel mode, only B, C or D would raise an alarm In blob mode only D would raise an alarm

Okay, that was a simple explanation. And I did not cover more details on min/max. But I hope you get the core idea..

Got the theory. Let's get back to your basement image

Okay, back to my basement and my 3 zones.

Which detection type should I use?

I personally feel to detect "humans", blob is the best. As I described above, it combines Alarm + Filtered + ensures that the pixel differences are contiguous and then does an algorithmic analysis to see if it forms 'blobs'

Pixels or percents?

What makes more sense to you? "Raise an alarm if 178 pixels are changed" or "Raise an alarm if more than 20% of my zone has changed?". To some, the latter makes much more sense. However, if you really want more fine grained control, you should use pixels. I used percent when I first started off, but then realized that pixels was more powerful when you are trying to eliminate false alarms.

(Pixels are especially useful if the difference in sizes is small. Example: its not possible to visualize the difference between 10% and 15%)

Selecting the right values

Using percents

(As of 2019, I recommend pixels, but I've kept this here for those who prefer percents)

It helps to think visually here. Let's go back to the zones I drew of my basement and try and visually place how a person and a pet would look in each zone. Here is a take:

Error creating thumbnail: Unable to save thumbnail to destination

• Zones and Depths: One of the learning for me was that don't make zones cover a lot of depth as far as the camera lens goes. Why? Well take a look at the image above. As a person or a pet walks away or towards the camera, it gets significantly bigger or smaller (right, that was not rocket science, but sometimes commonsense 101 helps)

• One of the advantages of using percents is that if you were to change your zone size, the percent settings will likely remain consistent (as they will be percentages of your zone area). In pixel mode, any change to the zone polygon will require updating the other values

• This is what my zone definition for the "stairs area" looks like, using percents:

Error creating thumbnail: Unable to save thumbnail to destination

Using pixels

(This is what I ended up using once I got comfortable with zones)

• This was updated Jun 2019, I don't have that basement camera any more, so I am going to use a different image
• I usually start with a Min/Max pixel threshold of 35 (that is, consider pixels alarmed only if the color different between the old pixel and the new one is 35 or more)
• For the min/max alarmed area, I draw a box inside my zone that represents an object size I think is appropriate. In the image below, I am trying to estimate what the size of a person would be in the zone. I use a mac - I simply hit Cmd+Shift+4 - that brings up a screen capture cross hair and as I draw the box, I see its width and height. Once I have a box with the dimension that I think is appropriate, I hit escape and simply fill in Min/Max Area = W*H of that box I used as a visual tool (the image shows a green box, just as a representation). In this case, my box was 42X67 pixels, so I fill in a min area of 2800
• You should also look at filling in a "max" area - this is to avoid sudden "blast of light changes" that raise an alarm. For example, if most of my zone pixels changed, it is unlikely its an object of interest. It is more likely the sun just blasted light on my driveway or a big shadow situation occurred. ZM helpfully tells you your zone area- in this case 92271. You could choose to put in a pixel value that is some large fraction of this value (maybe 90% of it = 83,000 or simply draw another rectangle to represent the largest object that is of interest to you and use that area value)

Tip: Don't try to get super precise in your first round: Use less aggressive values to begin with - that is, lesser area values. Keep increasing and testing till you reach a good threshold between bogus detections and real detections. Pixel based detections have a limit. You'll never get it perfect. For real object detection as an 'add-on' to motion, look at zmeventnotification, the machine learning based alarm detection extension to ZM

• (Note 1: the image is not to scale, so measurements will not tally if you are trying to draw boxes around the example image above)
• (Note 2: when you are measuring sizes, make sure you have not reduced browser scale. If you did, obviously, your pixel markings will be wrong because the image will be scaled)
• I then think about what might be the area inside that rectangle I drew that will have a continuous change in pixels. My guess here was 9x9 which is what I put into the Filter Pixels
• Finally, since I put a value of 2800 in the alarmed pixel area, obviously Min Alarmed Area > Min Filtered Area > Min Blob Area. So I set Min Filtered Area to around 35% of 2800 = 1000 and blob area to around 90% of filtered area (approx 900), the reason being in my estimate blob area should closely match filtered area of contiguous pixels for humans. This is my guess *shrug*

Lets see how ZM will use these values: (While the example below refers to percents, the same logic applies to pixels)

• Use the "blob" method to detect movement (which means first use Alarmed pixels, then use Filtered Pixels, then use Blob)

ZM's motion detection algorithm for this zone:

1. Set A = full zone pixels
2. (Min/Max Pixel Thres) In the *Full* area defined by the zone, check if there are any pixels that have have a 40 count difference in pixel color from a previous. Assign to Set B. If Set B = null, don't raise alarm, don't proceed with rest.
3. (Min/Max Alarmed Area) check if Set B is at least 6% of Set A and not more than 75% of Set A. If Set B does not fall in this range, don't raise alarm, don't proceed with rest.
4. (Filter Width/Height) In the set of pixels (Set B) that are different in color value of 40, check if there are pixels that are surrounded by 5 more pixels around them that are also different in color value of 40. Assign to Set C. If Set C = null, don't raise alarm, don't proceed with rest
5. (Min/Max Filtered Area) check if Set C forms at least 4% of Set A but no more than 75% of Set A. If Set C does not fall in this range, don't raise alarm, don't proceed with rest
6. (Min/Max Blob Area) use Blob logic on Set C to figure out how many Blobs are there. A blob that is at least 4% in size of Set A (full pixels) is considered a blob. Assign this to Set D.
7. (Min/Max Blobs) - If the # of blobs in Set D is less than 1, don't raise an alarm, don't proceed with rest
8. Raise Alarm!

Some other optimizations

There are other optimizations you can do:

• Another setting I found useful is to use "Alarm Frame Count". This is not part of Zones, but part of your monitor definition (Buffers tab). It specifies the minimum amount of alarm frames to trigger an alarm. Most of my cameras are on Wifi and my basement is farthest away from my AP, so I occasionally get smearing. Setting this to 3 reduces almost all smears raising an alarm
• As I wrote earlier, use maximum values in the zone definition to reduce 'change bursts' (significant pixel coloration changes due to spikes of light/shadows)